How can I simulate an ac to dc converter for medium voltage (10kv)?
u can use matlab
You can use a lot of free and paid simulators...question is what you would like to research, how big details about processes you need...If you need just check out the basic operation, LTSpice, which is free software can be useful
Salam, I found this excellent thesis, I think it might help you alot and solves your question. Please see the attached pdf file.
Read 5 answers by scientists with 15 recommendations from their colleagues to the question asked by Hossein Harimi on Dec 13, 2014
11 December 2014 1,771 6 View
10 November 2014 9,570 4 View
Read 20 answers by scientists with 145 recommendations from their colleagues to the question asked by Hossein Harimi on Nov 8, 2014
10 November 2014 3,853 19 View
10 November 2014 3,296 10 View
How to Stability Analysis of Nonlinear Systems with Simulink/Matlab ?
10 November 2014 3,539 8 View
There is clear evidence of changes in the composition of the greenhouse gases in the lower atmosphere, with CO2 in particular steadily increasing to its present level of about 400 ppm.
09 October 2014 6,961 9 View
What is the best(accurate) software for a power electronic simulation? Recommend: matlab/simulink/pspice/...
09 October 2014 4,954 5 View
What Are the Option Method research?
09 October 2014 9,761 2 View
Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.
09 October 2014 6,101 0 View
How can I design SST with Simulink/Matlab?
09 October 2014 7,709 1 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...
23 February 2021 1,761 1 View
Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...
22 February 2021 4,882 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...
21 February 2021 2,333 4 View
I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...
21 February 2021 3,043 3 View