Why have peaks at 590 and 798 cm-1 appeared in the IR spectrum of biogenic carbonate deposits?

04 May 2015 1,027 9 View

Is there anyone with research experience and interest in investigation of biogenic calcium carbonate polymorphs?

02 March 2015 7,850 3 View

Comparing the XRD patterns of mixtures containing CaCO3, how can I just roughly prove that one sample contains more aragonite than another one?

I have the XRD patterns of two samples which mainly contains calcite and aragonite (S1 and S2, see the attachments). How can I just roughly say that S2 has more amount of aragonite than S1?

01 February 2015 1,393 12 View

How can I find the urea concentration within a urea hydrolysis process?

01 February 2015 2,751 3 View

What does it mean when a reaction has a rate constant greater than one (K>1)?

I recorded the concentrations of a product during a reaction. There was an enzyme producing bacteria as catalyzer. Then I plotted the concentration changes versus time and fitted a modified...

31 December 2014 9,073 9 View

Why is a sample contained Calcite identified as Nitratine by XRD analysis?

I analyzed a sample contained calcite using XRD. The pattern attached. It was identified as nitratine by the related software searching the database of XRD patterns. As nitratine is isostructural...

31 December 2014 5,513 10 View

How much a fit model with the following statistics is reliable?

How much a model with: - Model p-value < 0.05 - Lack of fit p-value > 0.1 - R2=0.99, Adj. R2= 0.99, Pred. R2=0.99 - normal probability plot attached (residuals do not follow a straight...

09 October 2014 5,187 2 View

Is anyone familiar with full factorial design?

I did a 2-level full factorial design with 3 factors in order to find the significance of each factor and their interactions on a response. After ANOVA on non-transformed response, I found no...

08 September 2014 331 11 View

Generalized linear model or Least squares model?

I did the following full factorial experiments to find the significance of variables and fit model. I analyzed the data using the standard least squares model and generalized linear model (normal...

08 September 2014 2,582 6 View

How can I analyze a full factorial design with some undetectable responses due to interaction between factors?

08 September 2014 7,333 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View