How to coagulate the Polysulfone which was produced in DMSO as the only solvent of polymer synthesise process?

I have done some tests of polysulfone synthesise using the nucleophilic substitution route. in a some of the tests, DMSO was the only solvent that was used in the synthesise process. However I am...

03 April 2018 7,896 4 View

Can we use HPLC for measuring the amount of Bisphenol A (BPA) or disodium salt of BPA dissolved in DMSO?

I am doing a reaction between Bisphenol A (BPA) and NaOH to produce disodium salt of BPA. Firstly I use Dimethyl Sulfoxide (DMSO) as an organic solvent to dissolve the BPA and then add 50%...

01 February 2018 4,914 9 View

What is the wavelength of maximum absorbance of Bisphenol A (BPA) in UV-VIS?

I have prepared a clear colourless solution of BPA using Dimethyl Sulfoxide (DMSO) as an organic solvent. I have seen in the papers that the maxim lambda for the better absorbance of UV for BPA...

31 December 2017 9,565 2 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How can we obtain a modification factor for creep parameters?

I want to obtain standard creep parameters of salt rock by creep parameters of rectangular samples. Is there a modification factor to convert creep parameters of rectangular (prismatic) rock salt...

01 March 2021 7,131 1 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Which transition metal salt precursor is best for doping? Why?

I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...

27 February 2021 4,285 3 View

What are the saturated salt solutions that can give specific relative humidity of 35%, 65% and 95% for conditioning wood specimens?

Due to the unavailability of climate rooms, I want to carry out an experiment that require the use of certain saturated salt solutions especially those that can condition the wood specimen to 35%,...

25 February 2021 8,139 1 View

It is necessary to reflux the Schiff base and metal salts to obtain metal complex??

24 February 2021 9,166 3 View

How can I remove deep eutectic solvents from the medium?

Dear researchers, How can I remove deep eutectic solvents from the medium? You know, generally, deep eutectic solvents consist of ammonium salts and an acid group. Is there any alternative method...

22 February 2021 3,275 3 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View