How can I include space vector PWM converter in simulink just by using some gains? I've read that pwm converter can be modeled as a gain with a delay?

Muhammed Fasil @Muhammed-Fasil

05 July 2015 1 2K Report

Space vector PWM= Kpwm * e^(-sTsw).

What is the value i should give for Kpwm for space vector pwm?

e^(-sTsw) is for dead time? And for dead time i should use switching frequency as T??

Muhammed Fasil

Pulse Width Modulation

Badges
Science topic

Similar topics
Books

More Muhammed Fasil's questions See All

Why does the community engagement strategy not get priority in NCD prevention and control in developing countries?

NCDs are increasing alarmingly even in developing countries. Need to take participatory policies for prevent and control of NCDs.

30 July 2024 7,942 3 View

GC-MS calibrated for 16 EPA PAHs. Last 3 compounds show poor linearity. Response decreases. How to improve?

I have calibrated my GC-MS for 16 EPA PAHs using available methods. However, the last three compounds (Indeno[1,2,3-c,d]pyrene, Dibenzo[a,h]anthracene, and Benzo[g,h,i,]perylene) are not showing...

13 May 2024 4,966 2 View

How to Convert µg/mL standards to ng/m³ for PAH analysis in air via GC-MS?

Researchers typically use micrograms per milliliter (µg/mL) standards to calibrate gas chromatography-mass spectrometry (GC-MS) instruments for the analysis of polycyclic aromatic hydrocarbons...

12 May 2024 6,259 5 View

While doing propeller transient simulation on Ansys fluent, rotating zone contours corrupted. What is that reason?

I'm doing 3000rpm drone propeller computation on ansys fluent. First 1500 iteration steady state mrf zone is computed with SST k-w turbulance model. After convergence is done i change it to...

24 February 2024 9,935 1 View

How to calculate polydispersion index of a nanoparticle size? and does a PDI of 0.5 consider acceptable?

PDI value

30 November 2023 7,099 3 View

Is there an alternative chemical to ethylene glycol for IHC cryopreservation solution?

I am trying to optimize my antibodies for free floating IHC-IF on paraformaldehyde fixed mouse brain sections. I want to preserve my slices in an appropriate cryopreservation solution for later...

19 September 2023 6,240 3 View

Does a Post Doctoral from AACSSB accredited institute has value?

I would like to know about the future career prospects for a candidate pursuing Post Doctoral from an AACSSB accredited institute

16 August 2023 5,508 2 View

How can I detach my mesenchymal stem cells from flask?

Hello everyone. About three months ago, I could detach my mesenchymal stem cells obtained from 8-week-old mice with trypsin %0.25 on the 10th day in 3-4 minutes. However, now I can not detach the...

03 May 2023 6,159 5 View

Does anyone having this book as PDF format?

THE ZEBRAFISH BOOK A guide for the laboratory use of zebrafish Danio* (Brachydanio) rerio by Westerfield, Monte

20 February 2023 5,940 1 View

Coulomb interaction between Mulliken atomic charges?

How can i calculate coulomb interaction between muliken atomoc charges?

19 February 2023 6,785 0 View

How to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field in Techplot?

Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You

02 August 2024 3,615 1 View

Transfection in HEK293T cells?

Dear All, I am trying to transfect a pCDNA3.1 vector containing my gene of interest. The purpose is to figure out the localization of the protein of interest. I have fused the protein with GFP on...

31 July 2024 9,892 4 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

I need help with cloning a 200 bp insert and a 4,7 Kb pEGFP-N1 vector. How can I do it?

I've been trying to clone my N-terminal inserts in the comercial pEGFP-N1 vector. Initially, I cloned my N-terminal insert into a pGEMT-easy vector to ensure that the insert digestion was done...

09 July 2024 4,277 1 View

Cloning restrction digestion needed before sequencing?

Hello, recently i am an issue swith cloning where I am using the subclone method to insert my gene length is 1.5kb and my vector(pMAL-c6T) is 5kb I got the colonies which i screened through the...

04 July 2024 7,977 2 View

Why I am unable to get the expected insert at the cloning site?

I am trying to clone a gRNA (23 bases) into the Crispr cas9 pDirect23A vector by using restriction enzyme cloning. I have performed a complete experiment, starting with plasmid isolation,...

02 July 2024 5,448 2 View

What could be the expression profile of alkaline phosphatase from lactic acid bacteria?

I have already cloned ALP gene of L rhamnosus into pET22b+ vector. Cloning is already confirmed by restriction digestion and sequencing. Cloning is achieved in BL21(DE3), Codon+, Rosetta and Lemo...

02 July 2024 5,332 3 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View

Is it appropriate to use ARDL(autoregressive distributed lag model) with environmental Kuznets curve?

The underlying idea behind the environmental Kuznets curve is that GDP per capita initially increases environmental degradation but later reduces the environmental degradation as the result of the...

28 June 2024 949 0 View