How can I generate a SPWM signal for a 3 phase inverter in PSCAD?

More Jagabar S. Mohamed Ali's questions See All

How to connect the DS1004 R & D controller (Dspace) Pulse Signal to Semikron Driver Circuits (SKYPER® 32PRO R )?

DS1004 R & D controller (Dspace) output pulse signal output voltage is 10V, but Semikron Driver Circuits (SKYPER® 32PRO R )required 15V , How to connect?

02 March 2018 5,716 3 View

How to generate the ramp signal based on the angle?

i want to generate the linear signal with the different angle in MATLAB Simulink

03 April 2017 1,130 4 View

Which software tool is best for designing a circuit for journals?

I would like to know the best circuits design tool for articles or papers...

11 December 2015 3,332 2 View

Can anyone please help me in Efficiency of gate driver circuits while driving two switches (both are connected anti-series)?

can anyone please help me in Efficiency of gate driver circuits while driving two switches (both are connected anti-series)?

11 December 2015 1,931 5 View

Advantage and disadvantage of Anti-series connected IGBTs?

can any one hlep on Advantage and disadvantage of Anti-series connected IGBTs?

11 December 2015 9,854 4 View

Alternative Current Voltage waveform (AC Voltage Waveform), is this correct method to use?

Most of the books and papers mentioning AC Voltage waveform whether, this is proper method to use? other term DC Current and Voltage (Direct Current Current and Voltage).

07 August 2015 5,214 2 View

How can I measure common mode voltage in MATLAB/Simulink?

Thanks in advance for your replies.

02 March 2015 2,861 11 View

What are the parameters are considered, while selecting Multilevel Inverter?

What are the parameters are considered to select the multilevel inverter? There are more than 100 articles are published with novel multilevel inverter topology..still the researchers designing...

01 February 2015 904 0 View

Can anyone share a dvr based matlab simulation for multilevel converter?

I need to verify my new design of multilevel inverter? So does anyone have a dvr based multilevel inverter simulation that they could share?

01 February 2015 8,494 3 View

How can I simulate multilevel inverter in PSCAD?

Any one can help me to do simulation of multilevel inverter in PSCAD?

01 February 2015 2,698 1 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

I am working on my Master's thesis on the biogeography of the genus Ruagea and I would like to ask, could someone help me to check whether my result?

I created a file with my outgroup and ingroup species using Beauti, ran it in BEAST, viewed it in Tracer, and then used TreeAnnotator to create a file that I imported into RASP. Could someone...

28 July 2024 2,979 1 View

Fadi M. Albatsh

Please refer to Fig. 3(b) in my paper titled "Fuzzy based controller for dynamic Uniﬁed Power Flow Controller to enhance power transfer capability". Just use any reference signal and compared with carrier signal, then you can generate the PWM signals for IGBTs.

Shrinivas Vadhiraj

you could use number of triangular wave generator and one sin wave generator. with magnitude shift in triangular waves. you can achieve required switching sequence.