How can I design a channel estimation block for a multipath channel in Simulink?

Nooriana Nynza @Nooriana_Nynza

12 December 2014 1 1K Report

Which technique can I use to do the channel estimation of a multipath channel?

Syed Muslim Shah

Please see the many demos available in different versions of MATLAB/SIMULINK

Badges
Science topic

More Nooriana Nynza's questions See All

How do you implement a Multipath Rayleigh fading channel with more than one path delay in Simulink?

Whenever I'm putting more than one path delay values in the block, the BER remains around 0.5. Does anyone have a Simulink model to enlighten my problem?

31 December 2014 157 0 View

How can I convert a 3D signal into a 2D signal in Simulink?

I have a signal matrix ;192x3x2. I must convert it to 192x3. How do i do it?

31 December 2014 9,185 2 View

How to convert a 4-D signal into a 3-D signal in Simulink?

I have a signal : 400x6x2x2, I need to convert it to 400x2x2. Which block can i use to do it?

31 December 2014 8,372 6 View

Which simulink block can I use to do the power line channel estimate?

Channel estimation of power line communication channel.

11 December 2014 4,805 7 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View

Can we simulate light with matlab ?

Hi, I have to design a digital model of different types of lighting. Is it possible to simulate the lighting level from different sources (LED, incandescent, mainly fluorescence) with matlab...

28 January 2021 3,818 10 View

Algebraic Loop Problem in PV array Solution?

I am doing a project with PV array in Simulink. When I run small section of the total system i do not get an error. But when i integrate full system(my system model`s are completely okay) I get an...

18 January 2021 685 10 View

How to build aero engine fuel system online prognostics simulation model using Matlab, Simulink and Simscape?

17 January 2021 5,181 1 View

"The following block is not supported in Phasor simulation?

I am designing a control system for Hybrid renewable energy systems using Matlab/simulink/simscape, but currently having a problem. Whenever I run the simulation, I get the error shown below. "The...

12 January 2021 2,142 5 View

Steps for Hardware Implementation of Max Log MAP Decoder simulated in MATLAB?

How to implement max Log MAP algorithm turbo decoder on FPGA? Simulation is done on MATLAB. What are the next steps to be followed? Do I need to use HDL Coder feature in MATLAB? Is it needed to...

07 January 2021 4,405 4 View