I need a protocol for extracting ochratoxin A from green coffee beans for analysis on hplc, as well as the protocol for carrying out the calibr ?

ochratoxine A ; HPLC ; green coffee

29 December 2020 4,028 3 View

What is the most recommended multispectral-UAV to be used for delineating the shoreline?

Hi there, I am looking to purchase an UAV with an attached multi-spectral camera to use its images in delineate the shoreline. I need to take a vertical geo-referenced image (if possible) and...

21 November 2020 1,283 3 View

What would you do if MgSO4 did not fully dry your organic extract ?

Hi everyone, I used MgSO4 as a drying agent to suck all water droplets from my organic extract. However, even after adding MgSO4 three times and leaving it overnight, I still see some water...

14 September 2020 9,203 3 View

What multiphase model should be used to simulate the evaporation of an oil droplet in ANSYS FLUENT?

Hello, we have a sheet of Aluminium and some droplets of oil on it. The temperature of the sheet increases and the oil droplet evaporates in the air. The droplet has water and kerosene too and...

29 August 2020 2,268 3 View

How to activate the solid species tab in species transport in ANSYS Fluent?

Hello, I have to add a solid catalyst to the mixture but the tab is not activated. I have defined the solid material in the materials section but the list is showing the fluid materials only. How...

19 July 2020 4,930 3 View

How to make intervals in an ANSYS Fluent user defined function UDF to describe three different equations through time?

Hello, I have a plot shows the change of a quantity with time. How can we write a code in Fluent UDF to compile it ? I need a way to define the time intervals. From start to a specific moment, the...

30 May 2020 5,774 10 View

How to numerically estimate the polarity graph of a PEM fuel cell like the attached paper?

Hello, how to estimate the voltage and the current density of a fuel cell and put both on a single graph using CFD simulations? The paper is attached. Thank you!

04 May 2020 8,228 5 View

Which family name is correct for the insect species listed in the table below?

Hi friends The following table shows insect species from 3 orders. In conflicting sources, they are introduced from different families (family 1, family 2 and family 3). What do you think about...

02 March 2020 5,140 3 View

How to calculate the battery coefficients of Y and U by trial and error to estimate the current density and battery performance?

Hello I have a paper shows an idea to validate the battery performance by trial and error. How can we estimate the coefficients of Y and U and what is the experimental data needed for...

25 December 2019 1,502 8 View

How to charge a battery using a buck converter circuit in MATLAB SIMULINK?

Hello, I have a buck converter circuit to charge a battery but I do not know how to connect the battery's terminals to the output voltage. The snapshot is attached. If there is any other good...

08 November 2019 3,363 4 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View