05 August 2021 1 5K Report

Compare the three systems ( Fixed base, Base isolation, and Fluid Viscous Damper of braces corner) I need someone to help me with this system.

More Abdullahi Abdiaziz Abdi's questions See All
Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

No module named 'tensorflow.keras.backend.tensorflow_backend' ?

System Description Cuda 11.2 GeForce GTX 1080ti tensorflow version 2.4.1 keras version 2.2.0 python version 3.8 I was getting the below error when I try to run my code on the...

25 February 2021 6,673 2 View

Is it efficient to do liquid biopsy to investigate the gene expressions of the tumor?

To do liquid biopsy and look for specific gene expressions there are so many published papers. Thera are different protocols and procedures used to isolate circulating cell free RNA or mRNA from...

23 February 2021 7,326 5 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

What is the best way to improve the working potential window of a solid electrolyte?

My solid polymer electrolyte shows low bulk resistance show quite a low bulk resistance. However, the potential window (obtained from LVS) is very small. Please how can I improve the operating...

31 January 2021 3,340 9 View

Is carboxymethyl cellulose a better electrolyte host polymer than methyl cellulose and cellulose acetate?

I want to prepare a cellulose-based biopolymer solid electrolyte by solution casting technique. However, choosing the right cellulose derivative has been my major challenge. Among the many factors...

30 January 2021 5,355 3 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

Similar questions and discussions
How to find the target displacement to use in displacement control pushover analysis according to ASCE 41-17?

I am performing pushover analysis in Etabs of a steel braced frame but oI do not know what value should I use for target displacement. The height of the building is 20m. I want to know what value...

29 January 2021 2,190 2 View

What are the primary defects associated with welding druring construction-stages which might influence the capacity of the gusset-plate connections??

Dear researchers What are the primary defects associated with welding druring construction-stages which might influence the capacity of the gusset-plate connections in concentrated braced frames?...

06 January 2021 797 3 View

How can I get the axial stress for an inclined beam188 element on ANSYS APDL?

I modeled a bridge on ANSYS APDL and added cross bracings / diaphragms as shown below. The diaphragms are not straight along the x or y or z direction, they are inclides BEAM188 elements. how can...

14 November 2020 8,172 3 View

How to model inverted V bracings in opensees steel building model?

For the modelling of inverted V bracing, I need to provide node at the center of the beam to create the inverted V bracing but if I am providing the node as a hinge, the model is not running....

04 May 2020 7,939 4 View

How can I model the eccentrically braced frames system in the ABAQUS program or where can I find such an example?

I want to model the link-to-column connections in the ABAQUS program. But I need a sample resource.

27 March 2020 154 1 View

What are the alternatives for horizontal bracing system?

There is a steel pipe rack with normal framing system including horizontal and vertical bracing systems, all the connections of the horizontal bracing are defected, for some reasons it is nearly...

29 February 2020 1,583 3 View

I need some computer tomography files of dental jaws for its Finite element Analysis?

Actually for a project of FEA class, I need to perform FEA analysis for braces application. Please guide from where could I get the CT scans files. Because CT scan files can be converted to CAD model.

18 November 2019 8,693 1 View

I need some computer tomography files of dental jaws for its Finite element Analysis?

Actually for a project of FEA class, I need to perform FEA analysis for braces application. Please guide from where could I get the CT scans files. Because CT scan files can be converted to CAD model.

10 November 2019 4,913 1 View

How to model brace of Buckling Restrained Braces in ABAQUS ?

Hello everyone! I am new to abaqus and i am trying to model buckling restrained braces. I am finding difficult in modeling brace. As we know that the brace is composed of core (restrained and...

25 September 2019 446 2 View

If adding control devices such as viscous dampers should always decrease base shear or floor acceleration?

I have recently modelled some viscous and viscoelastic dampers in toggle brace arrangement in a 6 storey moment resisting steel frame and maximum floor displacement has been reduced drastically,...

08 September 2019 2,912 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close