How to incorporate a variable in damage model?

15 December 2020 7,284 2 View

Mathematical or computational modelling of protein oxidation?

I am looking for a research paper about the mathematical or computational modelling of protein oxidation (caused by reactive oxygen species).. I would really appreciate that if someone helps me...

17 November 2020 2,340 3 View

Can FEM model learn from experimental results?

I am looking for a research in which the finite element model was trained based on experimental results.

02 October 2020 9,277 19 View

Master thesis about the field of the luxury watch market?

18 September 2020 5,802 5 View

For connection between the bolt to the steel element, which kind of interaction should be considered on ABAQUS?

This design is to check for rupture in the steel element and the behavior of the bolt does not matter.

14 August 2020 6,580 2 View

Is it possible for anybody to help me for fix bridge modeling in OPENSEES?

I modeled a two-span concrete box girder bridge base on FHWA design specification, and now I recognize a problem in modeling because my first period is higher than I expected. With initial...

12 July 2020 415 3 View

Why does stresses evolve in only one element in Abaqus explicit?

I am trying to run my VUMAT code with a model in Abaqus/explicit. After that the run has been completed, I observed that the stresses have been evolved in only one element as shown in the attached...

27 May 2020 5,506 3 View

How to do baseline correction for DSC test data?

I have some raw DSC test data and I need to do baseline correction. I don't know how should I do it. I would appreciate it if someone can help me with this.

16 May 2020 8,273 7 View

Problem with nonlinear curve fitting?

Hello all, Actually, I am dealing with an issue that I can't get desirable results out of my curve-fitting problem. I used lsqcurvefit in the first place. Then, I added MultiStart to my code as...

30 April 2020 4,943 2 View

Tips on how to implement organic computing?

I'm researching the Self - Adaptive System of hospital systems.But I've had trouble figuring out how to do organic computing for self-adaptation in hospital systems.I am looking for an article or...

14 April 2020 1,743 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Why is the efficiency of viral mRNA electroporation in PBMC low?

Hello, I have been struggling with the electroporation of PBMC with HIV-I mRNA. Although the quality of the RNA generated is good, and the handling of the cells in meticulous, the frequency of...

27 February 2021 9,233 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View