How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Is a Strong correlation between the Moderator variable and the dependent variable an issue for moderation model (model 1) in Hayes PROCESS?

In a typical moderation model with one moderator, is it a problem if the moderator and the dependent variable show a strong correlation (say 0.85)? What if a strong correlation exists between the...

27 January 2021 4,937 4 View

Which syringe filters (e.g., PTFE, MCE, PVDF, CA, PES, etc.) are the best to filter TBS/PBS buffer (pH 7.5-8.5) and glycine buffer (pH 2-3) solutions?

I intend to purify antibodies from serum using the affinity procedure, and I need to filter the binding (TBS/PBS) and elution (Glycine) buffers before applying them to my solution.

06 January 2021 5,769 3 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

How to assign initial stress to a coating in Abaqus?

Hello! I am trying to define/assign initial stress to a coating I modeled on a substrate. I defined the coating using "skin" function. I have tried "predefine filed" in load section. But it only...

10 December 2020 2,921 8 View

How to model a multilayer coating in ABAQUS?

Hello! I'm trying to model a multi-layer coating on a substrate in abaqus. The layers are homogenous and isotropic. My question is how should I approach the modeling? WHAT I'VE TRIED SO FAR: I...

09 December 2020 1,235 3 View

How can I calculate Nusselt number by using this equation (Nu = ht.gradTx * nx + ht.gradTy * ny + ht.gradTz * nz) step by step in COMSOL?

Calculate the Nusselt number using the COMSOL Program

09 December 2020 3,354 3 View

How to calculate sulfur loading of lithium -sulfur batteries using Li2S8 catholyte?

I am gonna use Li2S8 catholyte to introduce active material to cathode instead of using sulfur. May anybody kindly guide me about the way I can calculate the amount of sulfur (g/cm2) loaded on the...

07 December 2020 7,556 2 View

How to great data visualization and what example for it ?

i need explain data visualization and what type it and how great it by excel or other program > paper attached for help

30 November 2020 1,159 2 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How could I process data in RCT to include it in meta-analysis?

I'm in the process of doing a meta-analysis and have encountered some problems with the RCT data. One of my outcom is muscle strength. In one study, I have three different measurements of muscle...

25 February 2021 7,603 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

Please. Could you help be in implementing Fractal Discrete Cosine Transform algorithm in Matlab?

I do need the Matlab code of Fractal Discrete Cosine Transform (FDCT). Can anyone who has already implement this code, help me with the implementation of this transform?

24 February 2021 5,602 2 View