How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

High pass filter on EMG after Bandpass(Boonstra2012)?

Hi all, I am currently trying to carry out an EMG coherence analysis, prior to this I have been reading some papers. I can understand the Bandpass implication from range A Hz to B Hz, but from...

25 November 2020 7,461 1 View

How can I design resin column for test?

I'm interested in the research field of ion exchange resin. I want design about resin column with acryl for test. How do you usually design the diameter and length of small columns for test? I...

13 October 2020 3,443 2 View

How to purify a recombinant protein from Ecoli to reach a cell culture purpose?

05 October 2020 502 7 View

How do I change to make an insoluble recombinant protein to a soluble protein?

How do I change insoluble recombinant proteins to soluble proteins? My recombinant protein is Aldose dehydrogenase from bacterial with around 35.0 kDa size. Now, My expression vector and...

05 October 2020 1,840 2 View

Can XRD determine inorganic material composition?

From my understanding, XRD is used to determine phase identification of a crystalline material. Is it possible to use XRD to determine the composition of a certain material? I think XRF or EDS is...

15 June 2020 9,211 8 View

What are the steps before perform Normality Test?

Hi all, I m a Master Students. I need to perform Normality Test in my study. I have 5 independents variables and 1 dependent variable. Each independents have 6-8 questions and dependent variable...

14 May 2020 9,015 3 View

How to fit the Gaussian curve based on the moment of power spectrum?

I want to make a spectral correction curve of my light source to resemble the Gaussian spectrum. This literature said, ".. The dashed curve is a Gaussian fit with a center wavelength of 833 nm...

20 January 2020 8,950 2 View

Sodium chloride solution saturated vapor pressure at sub zero temperature?

Can anyone suggest where to find the data or any equations related to the salt solution vapor pressure at sub-zero temperature? Many thanks!

24 December 2019 7,741 2 View

Can aequorin being stably transfected in cell line?

We are trying to transfected the aequorin plasmid into neurons, how can aequorin being stably transfected in cell line?

09 September 2019 1,386 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to access MSCI KLD Stats and Sustainalytics?

Hello all, I'm currently working on my undergraduate thesis and I'm having difficulties trying to access KLD Stats and Sustainalytics because my campus Airlangga University and apparently other...

02 March 2021 8,525 1 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View