how fracture toughness can be found out by four point bend test? and why only three point bend test is used for fracture toughness?
HI MR. Shivang Jayswal
I Attached to you Standard Test Method for
Measurement of Fracture Toughness ASTM 1820 and A review of experimental approaches to fracture toughness evaluation at the micro-scale.
Best Regards
I am trying to model a quasi-static compression of a complex structurAl geometry. The experiment was done at 2 mm/min of loading. I am using ANSYS Explicit Dynamics. I’m also using Automatic Mass...
20 April 2024 2,934 4 View
The process of collecting core samples in cases of structural failure is essential for understanding the root causes and evaluating the integrity of the structure. While specific guidelines may...
05 November 2023 4,488 4 View
How can one determine the Degree of Reaction (DOR) using Thermogravimetric Analysis (TGA)? In modern times, blended mixes with various Supplementary Cementitious Materials (SCMs) are common,...
14 October 2023 4,741 2 View
Relaxation response is an event facilitated by several practices and lifestyle. I am working on such a practice.
25 September 2023 7,115 3 View
(suppose d = 5 cm, intensity at 5 cm = ?)
27 May 2020 7,881 0 View
I observed that the low calcium fly ash is more reactive than the high calcium fly ash. Is there any relation between C/S ratio to the reactivity and strength of concrete???
03 January 2020 1,176 3 View
Can we consider the percentage of mass loss between 420 ⁰C to 500 ⁰C as the percentage of calcium hydroxide? or any other method are there to calculate the percentage of calcium hydroxide from TG...
14 November 2019 8,330 1 View
How can we measure the toughness of mortar or concrete of unnotched section through load deflection method? any standard are available for measure the toughness of unnotched beam?
21 July 2019 1,434 4 View
Exactly how one can prepared the cement sample for XRD and TG/DTA? how can stop the hydration of cement?
07 July 2019 5,859 10 View
The validation is done based on a time scaled ground motion (response of shake table). However, for this validated numerical model, do the time histories (to be used for incremental dynamic...
09 September 2018 5,237 5 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Cross-slip, twinning and fracture are major deformation modes adopted by loaded materials. It appears sound that these apparently different deformation mechanisms can be analysed on the equal manner!
15 June 2024 8,477 3 View
Hello all, I need to pre-crack a steel specimen with the following dimensions. W = 25mm, an = 6mm, B = 5mm How do I identify the force required for the pre-crack initiation?
30 May 2024 1,285 2 View
Trying to estimate the DBTT temperature for A572 & RHA steel based on alloying composition.
20 May 2024 8,060 8 View
Currently, there are numerous blood biomarkers that have been linked to fractures and increased fracture risk (for example, IL-6). Considering the current evidence, which ones do you think are the...
10 May 2024 6,097 2 View
Can we restrict the vertical and horizontal displacement in two directions for the lower semicircular in bottom hole of CT specimen and apply incremental displacement in the upper semicircular in...
09 May 2024 5,273 4 View
I need to design a component with GGG40-18 material. Design also needs to be checked for Low cycle fatigue. I used to design for LCF based on strain v/s number of cycle data. I got properties from...
22 April 2024 3,102 0 View
Short answer
22 April 2024 665 0 View
I am searching for an alternative to chromel-alumel thermocouples for our stand. The point is to find something better to use in Ar-O2 plasma (approx. 400 °C, 1.0*10^(-3) Torr). The only relevant...
02 April 2024 7,842 0 View