is possible to prepar the carbon nanotube as collide by pulsing Nd yag laser?
how can be checking and test the nanoparticles, have uniform distribution or not in the colloidal species?
11 December 2018 4,539 10 View
Which is the suitable materials to composite with Nanoparticles TiO2?
09 October 2018 7,233 8 View
In laser ablation in liquids, can be use the electrooptical single crystal such as LINbO3 or KTP immerses in water or solution to prepare nanoparticles?
07 August 2018 7,553 0 View
What are the most parameters must be electrically investigated of thin nano particles films?
05 June 2018 2,505 4 View
In preparation of the nanoparticles colloidal, How the polarity of the solvent liquids influences on the optical properties of these particles?
05 June 2018 3,357 3 View
Is there a relationship between the size of nanoparticles with length of absorbance waves
05 June 2018 2,800 5 View
Is the nanotechnology belong to Physics Sciences, Material Engeneering, Chemistry or Materials Sciences?
05 June 2018 1,821 5 View
Which is more efficiency for obtains harmonics generations, large or smaller nanoparticles?
05 June 2018 762 0 View
It is possible to produce nanoparticles colloidal from single crystals. Such as LiNBO3 or KDP as atarget in water using pulsing laser(laser ablation) ?
05 June 2018 4,849 0 View
In laser ablation which is more effective on the properties of the obtained nanoparticles, the number of pulses or the laser influence?
04 May 2018 4,708 3 View
In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...
03 March 2021 1,682 3 View
I anwar by adsorption or reaction ..but it is either more method...
02 March 2021 4,811 2 View
I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...
02 March 2021 7,626 1 View
Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...
01 March 2021 1,907 3 View
I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...
01 March 2021 5,475 2 View
I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...
28 February 2021 4,890 3 View
Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...
26 February 2021 10,014 3 View
Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...
26 February 2021 4,026 5 View
In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...
26 February 2021 2,435 4 View
I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...
26 February 2021 8,183 3 View