FEM analysis of annular fins

More Nilanjan Chaudhuri's questions See All

Can anyone suggest how to manage a Make to Order scenario with a high product variety?

Please give an example of a firm which has done this.

03 April 2013 6,962 0 View

Can anyone help me out in deriving the functional of a particular differential equation of the form - (d2T/dr2)+(1/r)*(dT/dr) = 0 , where d2T/dr2 repr...

FEM analysis of annular fins

31 December 2011 4,073 3 View

Any idea about variational formulation of annular fins????

Hello everyone I wish to do research work in the variational formulation of annular fins..

08 September 2011 3,857 5 View

Hello everyone...I wish to apply for DAAD from India in German Universities.Are any german professors in this group?? I wish to do my project in FEM.

Daad

08 September 2011 7,556 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

Is there a Constitutive model for concrete with Sea-Sand?

Hi I am running a simulation in Abaqus for a concrete beam. Its fine aggregate replaced with sea-sand. I was wondering if I could find studies that measured the ultimate strain of concrete made...

22 February 2021 6,409 2 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

Nilanjan Das Chakladar

Are you using abaqus?

Nilanjan Chaudhuri

might use that if u advise to... was currently doing it on ansys..

Hussam Ali Mohammed

Please check references below.. hope it will be helpful for you… Regards…

https://file.scirp.org/pdf/MNSMS_2017072016050999.pdf

http://www.arpnjournals.com/jeas/research_papers/rp_2012/jeas_0612_718.pdf