Exporting analog signals from simulink model to Pi model 2. Deliberations?

01 January 2016 1 6K Report

Dear all

Any deliberations on exporting analog signals (like voltages in SimpowerSystem) from a Simulink model to a Raspberry Pi (of course having ADC converted within the model) say, to its GPIO pins. Thanks.

Shashank Vyas

felt no need for the same for the task wanted to be executed...used UDP protocol instead to send those analog signals to Pi from Simulink model....use of UDP send/receive blocks and normal/eternal ode of simulation serves the purpose..Thanks

Badges
Science topic

More Shashank Vyas's questions See All

Can I seek expertise in validating precursor signals to un-intentional islanding of PV inverter?

IEEE 13 node feeder has been modeled without a voltage regulator block. The load flow results in simulink are little more than 65% accurate. I connect the HydroQuebec (R) 100 KWp PV model on node...

03 April 2015 5,314 2 View

How can I look for data of unintentional islanding events of renewable energy generators in a distribution grid?

I am researching on using data analytics for addressing the issue of unintentional islanding in distribution grids given that renewable energy based generators will increase their penetration. I...

02 March 2015 9,354 1 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Why am I getting 'Infinity' and 'NaN' in my mixed-mode energy release values?

Hi everyone, I am currently running a mixed-mode simulation of a DCB using a user-defined cohesive zone model (UEL), however, the results I am getting don't make sense. I used the same UEL for...

24 February 2021 4,157 1 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View

How to eradicate the deteriorated contact resistance in the electrical or electronic devices, like SCR or contactor' pin cable ?

Through years operation, some of the devices' pins connection gradually become worse and finally burn out due to the high temperature at the connection point. We can check out these risk points...

04 February 2021 7,401 5 View

Will it be possible to get IC:50 if we target cancer cell line with antibody drug conjugate (ADC) that have 50% less antigen positive cells ?

Is it possible to attain IC50 if my target cells have less than 50% antigen expression ? For example: Cancer cell line XXX is showing 35% of expression of cell surface antigen YYYY, if i...

04 February 2021 2,711 3 View

Can we simulate light with matlab ?

Hi, I have to design a digital model of different types of lighting. Is it possible to simulate the lighting level from different sources (LED, incandescent, mainly fluorescence) with matlab...

28 January 2021 3,818 10 View