How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

How does GROMACS calculate the average structure of proteins?

I want to get a average structure from a pdb file containing multiple models. I used the command below: gmx cluster -f input.pdb -s topol.tpr -cutoff 20 -method gromos -av GROMACS...

25 February 2021 6,314 1 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

R/Python package for time-intensity or progressive profiling in sensory evaluation?

Hi I've been looking for a stat package for my sensory evaluation data (progressive profiled which is a multi-timepoint version of descriptive analysis). Is there any available one to...

08 February 2021 9,170 3 View

How can I make sure the simulation results of the water droplet impacting on the wall using the FLUENT agree with the experimental results?

Dear researchers, I am modeling the process of the water droplet impacting on the wall with a constant contact angle. The specific calculation parameters are as follows: The droplet diameter is...

24 January 2021 1,020 5 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

How can I calculate packing density of particles by fomulas or softwares?

I have all data of particles, such as size distribution, or numbers. Is there any way that I can calculate the packing density of these particles? Assume that all particles are circular.

05 January 2021 4,272 2 View

After cellulose is regenerated in water, a cellulose hydrogel is formed. I want to know if there is crystallinity inside the the hydrogel?

After cellulose is dissolved and regenerated in water, a regenerated cellulose hydrogel is formed. I want to know if there is crystallinity inside the hydrogel, or it will not crystallize until it...

04 January 2021 7,466 4 View

How can I fix the density of system in coarsed grain simulation?

In the process of obtaining the nonbond potential of the Coarse-grained(CG) model, I need to simulate the CG model mapped from the conformation of all atom(AA). AA simulation process is...

02 January 2021 3,643 1 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View