How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Greetings Doctors, If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers?

If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...

04 February 2021 4,648 4 View

How to simulate Sloshing water using Dynamic mesh in ANSYS Fluent ?

I am trying to model sloshing water in a tank in ANSYS Fluent using Wall motion. BUT it seems that System coupling is not responding to wall motion and it works only with Dynamic mesh.

20 January 2021 2,963 3 View

How can i properly obturate more than one canal at the same time in one tooth using CLC without interfering with the canal positionand accessory file?

#Rootcanal #Obturation #Endodontics

29 December 2020 5,982 2 View

Is it possible to deliver hydrophilic drugs to lymphatic system after oral administration? what kind of drug delivery system could be used if (yes)?

Is it possible to deliver hydrophilic drugs to the lymphatic system after oral administration? what kind of drug delivery system could be used if (yes)?

01 July 2020 1,793 1 View

How to estimate the compressor's weight/mass with a given pressure ratio and mass flow rate ?

I want to estimate the mass (does not have to be accurate) of a centrifugal compressor knowing the required mass flow rate and pressure ratio. Thanks in advance!

07 May 2020 2,487 1 View

How to design load curve to take measurements for solar heater through the day?

I make measurements for the master thesis of solar heater. I need to design a load curve to obtain measurements for natural consumption of people. I will discharge solar heater tank through the...

29 February 2020 1,413 4 View

Is there any good references for autocorrelation testing of time-series data?

I'm looking for any recommendations on solved problems/resources on Autocorrelation statistical testing of time-series data such as : 1. Lagrange Multiplier (LM) testing. 2. Durbin-Watson...

28 November 2019 5,026 3 View

Can sodium content of a drug affect ECIS impedance readings?

In experiments to detect effects of GPCR agonists on barrier function of endothelial cells, different agonists can have different sodium contents. In my case, I use the agonists at different...

18 November 2019 3,261 1 View

What is the Future of bioethanol as a road fuel?

What is the future of bio-ethanol as a road (car) fuel? Do you think electric vehicles will take over the market very soon that no need for biofuels for road transportation?

17 May 2019 7,000 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What kind of intervention will be relevant to increase motivation among young sport trainees?

Any suggestion on what book to read is also welcome.

03 March 2021 1,646 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View