WHAT ARE THE MAIN PEAKS IN THE FTIR AND RAMAN SPECTRA RELATED TO THE POLYSTROL/C70 FULLERENE SYSTEM?
Dear Elyor Tursunkulov
The FTIR and Raman spectra of the polystyrene (PS) / C₇₀ fullerene system show characteristic peaks from both components. The presence of C₇₀ can cause shifts or intensity changes in some peaks due to intermolecular interactions.
1. FTIR (Fourier Transform Infrared) Spectroscopy
Polystyrene (PS) Main Peaks:
C₇₀ Fullerene Main Peaks:
Effects of C₇₀ in FTIR:
2. Raman Spectroscopy
Effects of C₇₀ in Raman:
Conclusion:
Thanks
Dear Elyor Tursunkulov,
Perhaps you will find the article about the electronic properties of C 60 in polystyrene and hexane useful?
It is available in Russian:
Absorption and fluorescence spectra of C 60 fullerene concentrated solutions in hexane and polystyrene at 77–300 K
Article
Full-text available
Journal of Applied Spectroscopy
Vladimir S. Pavlovich, E. M. Shpilevsky
and in
Photoprocesses in biomolecules, carbon nanoparticles and polymer solar cells (Full text)
Book
THANK YOU FOR YOUR ANSWERS,Vladimir S. Pavlovich,Md. Rehan Alam
We know if there is a beard in the sepals of the iris. Which factors can lead to a change in this morphological sign?
04 February 2021 8,847 0 View
The answer of this question is important for young researchers. Because there are many journal in Scopus data base, which publish unlimited articles and are active in just one or two year. These...
26 July 2020 5,732 3 View
Nowadays, DFT calculation is important part of chemistry, but many valuable softwares are required licences and very expensive. This phenomenon is biggest obstacle to research in poor Universities...
01 January 1970 6,582 17 View
Do these peaks in the curve indicate primer dimer or non-specific products?
01 August 2024 7,466 0 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 435 3 View
I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...
16 July 2024 6,918 7 View
During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...
08 July 2024 1,330 0 View
I synthesized some paramagnetic cobalt and nickel complexes (expected to be Co(II) and Ni(II)) using a bidentate ligand - N of pyridine ring (aromatic) and O of P=O (aliphatic), and I obtained...
03 July 2024 3,410 4 View
I'm trying to fitting Cu Auger peak into various state (Cu0, Cu+, CuI etc..) In Cu0, one of the peak's FWHM is 0.84 but when I try to enter smaller value than 0.89, "input error" is occured. How...
02 July 2024 4,932 3 View
Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...
30 June 2024 1,063 4 View
Hello everyone, I'm facing an issue with EDS software that prevents me from obtaining atomic or weight percentages for my scan. However, I do have access to the raw data, which shows intensity vs....
29 June 2024 6,664 14 View
Hi all, I have few XRD files of MoVO oxides. These are newly synthesized compounds. Can anyone suggest me, how can check my XRD files from database? I want to match my XRD peak to the database. Is...
24 June 2024 6,448 3 View
fiber powders will be used as a reinforcement.
23 June 2024 10,027 3 View