Eaton's method for Pore pressure prediction?

Abdulquadri Alabere @Abdulquadri-Alabere

06 September 2020 1 7K Report

I am currently working on pore pressure for a high pressure, high temperature interval in the Niger Delta. The normal Eaton's exponent of 3 does not accurately predict the shale pore pressure for the HP/HT interval. What other options do I have?

Ahmed E. Radwan

Eaton's exponent is not working in every basin worldwide, you should try and error until you got a satisfied result matching your calibration points

Badges
Science topic

More Abdulquadri Alabere's questions See All

What is the best way/method to do reliability test (e.g. Cronbach Alpha Test) on a data set?

Is is advisable to do reliability test (e.g. Cronbach Alpha Test) for a whole data set? Or is it okay to do it for a segment of data with the same characteristics.

26 May 2024 3,594 1 View

What is the best sampling frame to use for a study area with no finite population?

I am currently undergoing a research on: The Spatial Analysis of the Incidence and Users' Fear of Crime at Motor Parks in Ibadan. What is/are the best method for determining the sampling frame or...

29 January 2023 2,225 2 View

What type of statistical analysis tool(s) is/are best for the following research hypotheses?

I am undergoing an analysis with three research hypotheses. However, I am confused on what type of statistical tool is best used for the hypotheses. These hypotheses are: 1. There is no...

21 October 2022 7,241 7 View

Does socioeconomic status/characteristics influences crime occurrence, crime victimization and crime perpetration?

In crime analysis, I oftentimes analyze the socioeconomic status of respondents. However, many of my results have shown that they do not necessarily influences crime experience of respondents....

16 May 2022 1,058 6 View

Is there an analytical solution for heat conduction in a 1-D slab with both adiabatic and convection boundary conditions ?

By "both", I mean one end of the slab is insulated, the other end is exposed to cooling/heating fluid. The boundary conditions for available - or at least, those I'm aware of - analytical...

14 September 2021 8,410 4 View

How to apply data science in hydrocarbon exploration?

Dear exploration IST, I am struggling with developing a personal development plan on learning how to apply data science to hydrocarbon exploration so as to remain relevant in the industry. I need...

31 August 2020 757 2 View

Is model validation not compulsory when using scale modelling concept in engineering?

Unlike computational fluid dynamics (CFD), I have noticed that most studies reporting the use of physical scale models for airflow or temperature study rarely present any information on model...

01 January 1970 964 5 View

Method of Conducting Reliability Test (e.g. Cronbach Alpha Test)

What is the best way/method to do reliability test (e.g. Cronbach Alpha Test) on a data set? Is it advisable to do reliability test (e.g. Cronbach Alpha Test) for a whole data set? Or is it okay...

01 January 1970 2,690 1 View

Determining population of study and Sampling Techniques

I am currently undergoing a research on: The Spatial Analysis of the Incidence and Users' Fear of Crime at Motor Parks in Ibadan. What is/are the best method for determining the sampling frame or...

01 January 1970 3,469 3 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

Does the delta function actually make sense to use on point particles?

The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.

31 July 2024 10,109 3 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View