Does Tg between first and second heating shift for foam sample?

24 November 2019 0 9K Report

Under identical test conditions, does Tg measured using DSC shift between the first heat and second heat? What causes such a shift?

Size, shape and weight, rate of heating, etc affect Tg. What about Tg of foam vs. solid sample of the same material?

Badges
Science topic

Similar topics
Heat

More Amit Dharia's questions See All

How to show a protein is being dimerized in SDS-PAGE gel?

A protein dimerizes through CTD. I have expressed CTD of protein with two different tags. Now, I want to show that these CTD of protein dimerize in a pull-down assay. But my doubt is that if the...

29 January 2021 7,529 4 View

What are the impacts of pKa1and pKa2 in drug absorption ?

Pregabalin is a crystalline solid with a pKa1 of 4.2 and a pKa2 of 10.6. what insight can i get from this aforementioned information during drug design. What is the difference between pKa1and pKa2.

28 December 2020 7,237 3 View

How to deal with negative factor loadings while performing PCA-MLR to calculate quantitative source contribution in air pollution studies ?

If I am getting some negative values in factor loadings while performing principal component analysis (PCA), then I should use that negative values to calculate daily source contribution using...

22 December 2020 5,248 1 View

What are the source markers of Naphthalene, Acenaphthylene and Acenaphthene in ambient atmosphere ?

Is any article available which reports the sources of these PAHs ?

22 December 2020 8,738 1 View

Why high infiltration in OM treated plot?

We are carrying out trial in the glasshouse where we are comparing the infiltration rate in sodic soil in two different treatments Polyacrylamide vs organic matter ( lucerne pellet). within 27...

25 November 2020 8,787 3 View

Where can one download data (csv, excel) for average daily values of AQI (air quality index) in popular cities, like, Delhi and Mumbai in India?

Air pollution has become a very big problem in Indian cities, especially Delhi. It requires immediate attention and we need to soon understand the trends, provide forecasts for future, issue...

19 November 2020 1,433 3 View

What is the best feasible method to plot DISTANCE vs LST graph?

The above question is intended to be answered in reference to the reduction of the urban heat island by the river.

22 October 2020 7,732 4 View

Which type of measuring instrument can be used to measure hot thermic fluid flow rate?

The flow rate of thermic fluid is less than 1 L/min and temperature ranges from 25 - 200 degree Celsius with a pressure limit of 5 bar.

06 October 2020 5,612 11 View

Can anyone endorse me for arXiv.org?

Hello, I need an endorsement to submit my preprints in arXiv.org. I am in the bioinformatics research field. The arXiv requires an endorsement for me because my institution doesn't provide any...

02 October 2020 1,041 4 View

How to calculate a flow rate over the broad-crest wear for this conditions?

How to find a relationship between velocity and weir landing length (X') as shown in figure?

28 September 2020 7,159 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View