Does milling of treated alumina particles cause degradation or destruction of the silane layer?

01 January 2015 1 4K Report

I want to make milling for treated alumina due to agglomeration after drying in oven.

Certanly silane layer will suffer. Strong particles grinding will take place in a ball mill or planetary mill. I only could suggest you alumina colloidal grinding in silane solvent and only after that drying in oven. It will help to form new sliane layer as grinded surface generated, which decrease agglomeration

Badges
Science topic

More Fathie Kundie's questions See All

Publication in Dental journals?

Some journals in Dentistry field require Data, Sources & Study selection in the abstract. Can anyone provide clear definitions for these terms? what are differences between Data and...

09 October 2016 8,921 0 View

Material Characterization

I need a clear definition for Fracture resistance and how can be measured in polymer composites?

31 December 2015 2,334 1 View

Does anybody use ultrasonic probe sonicator?

I disperse nanoalumina particles in Methyl methacrylate (MMA) monomer via probe sonicator at amplitude of 70 for 10 minutes, but the generated temperature is high which lead to some evaporation...

04 May 2015 8,166 5 View

Can you help me to avoid porosity in PMMA?

I mix PMMA with Benzoyl peroxide, and then add EGDMA to MMA. Finally, I mix the mixture with the liquid and subject it to heat treatment. Porosity about 15%.

31 December 2014 3,561 4 View

Can core/shell method be applied in MMC and CMC?

31 December 2014 909 1 View

How do I calculate porosity using water?

I want to calculate porosity in PMMA samples.

31 December 2014 3,855 17 View

What is the best coupling agent to mix alumina nanoparticles with a polymer?

I use Poly(methyl methacrylate).

31 December 2014 7,429 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

Is the black sediment consider as sand? If not, how can I filter it out?

Hi researchers! I'm working on soil texture analysis, and the end result for sand is doubtful because there is black sediment appearing after drying, as shown in the figure. Is it considered sand?...

30 July 2024 557 2 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View