How to show a protein is being dimerized in SDS-PAGE gel?

A protein dimerizes through CTD. I have expressed CTD of protein with two different tags. Now, I want to show that these CTD of protein dimerize in a pull-down assay. But my doubt is that if the...

29 January 2021 7,529 4 View

What are the impacts of pKa1and pKa2 in drug absorption ?

Pregabalin is a crystalline solid with a pKa1 of 4.2 and a pKa2 of 10.6. what insight can i get from this aforementioned information during drug design. What is the difference between pKa1and pKa2.

28 December 2020 7,237 3 View

How to deal with negative factor loadings while performing PCA-MLR to calculate quantitative source contribution in air pollution studies ?

If I am getting some negative values in factor loadings while performing principal component analysis (PCA), then I should use that negative values to calculate daily source contribution using...

22 December 2020 5,248 1 View

What are the source markers of Naphthalene, Acenaphthylene and Acenaphthene in ambient atmosphere ?

Is any article available which reports the sources of these PAHs ?

22 December 2020 8,738 1 View

Why high infiltration in OM treated plot?

We are carrying out trial in the glasshouse where we are comparing the infiltration rate in sodic soil in two different treatments Polyacrylamide vs organic matter ( lucerne pellet). within 27...

25 November 2020 8,787 3 View

Where can one download data (csv, excel) for average daily values of AQI (air quality index) in popular cities, like, Delhi and Mumbai in India?

Air pollution has become a very big problem in Indian cities, especially Delhi. It requires immediate attention and we need to soon understand the trends, provide forecasts for future, issue...

19 November 2020 1,433 3 View

What is the best feasible method to plot DISTANCE vs LST graph?

The above question is intended to be answered in reference to the reduction of the urban heat island by the river.

22 October 2020 7,732 4 View

Which type of measuring instrument can be used to measure hot thermic fluid flow rate?

The flow rate of thermic fluid is less than 1 L/min and temperature ranges from 25 - 200 degree Celsius with a pressure limit of 5 bar.

06 October 2020 5,612 11 View

Can anyone endorse me for arXiv.org?

Hello, I need an endorsement to submit my preprints in arXiv.org. I am in the bioinformatics research field. The arXiv requires an endorsement for me because my institution doesn't provide any...

02 October 2020 1,041 4 View

How to calculate a flow rate over the broad-crest wear for this conditions?

How to find a relationship between velocity and weir landing length (X') as shown in figure?

28 September 2020 7,159 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View