I need to mix two polymers(here the two polymers are taken as the constituent of two paints ) in Ansys Fluent. Hence I need to find out the variation of viscosity of the mixture.
Would you contribute to a new journal through papers, editorial board, and reviewing? What is your opinion?
04 March 2024 8,502 3 View
Is it just a theoretical concept? If so, how is it modeled? Is it a consequence of poor physical contact?
01 August 2023 6,168 2 View
I am working in Barium ruthenate triple perovskites. I have been observing proper downward peaks at about 30 K, with the minima shifting to higher temperature for higher frequencies. The magnitude...
08 June 2023 7,402 3 View
I have a polymer film. I want to do the CV, GCD and EIS studies using a three electrode system. KOH is the electrolyte, Pt wire as the counter and calomel as the reference electrodes.
23 February 2023 6,245 3 View
I have identified two different strains of bacteria of same species, during my experiments i could also find the difference in tolerance of these bacteria in same pH and temperature. Is this...
19 October 2022 1,066 0 View
I have downloaded 1 km resolution data from chelsa website.The monthly raster images are in kg/m2/month. I need them to be in mm/month for my analysis. Kindly help me with this problem. Thank you
06 July 2022 9,598 3 View
I have a site disordered system, with multiple ions at particular site. I need to refine the occupancies maintaining the chemical formula and total occupany of 100% in fullprof. I tried giving...
18 March 2022 3,726 7 View
I need to disperse CNT and PVA for prepare a composite. Can anyone suggest the best solvent for dissolving both CNT and PVA?
14 December 2021 5,067 6 View
I am working on perovskite oxides and am stuck with discrepencies in the effective magnetic moment of my compound from C-W fit as compared to theoretical magnetic moment with various spin states....
27 October 2021 7,106 3 View
I would like to understand what is happening inside the cathode, anode, and the electrolyte of a lithium-ion battery. I can take good journals too.
01 September 2020 6,920 3 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.
29 July 2024 6,350 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.
21 July 2024 3,045 3 View
For which types of polymers, the crystallization peak in heating cycle of DSC test can be observed and for which types cant? In another word, when this exothermic crystallization can be observed...
18 July 2024 348 3 View
Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...
18 July 2024 7,258 3 View
I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...
16 July 2024 5,031 1 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...
12 July 2024 2,768 1 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View