Does any one same drawing of IGBT driver like this?

Hossein Almasi @Hossein-Almasi

27 May 2023 0 584 Report

For common to the IGBT with need interface between plc and IGBT, we want some offer to improve this board.

Badges
Science topic

Similar topics
Geoscience
Cartography
Mapping
Maps

More Hossein Almasi's questions See All

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How can I find eddy size distribution in ANSYS Fluent?

Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...

01 February 2021 731 1 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

How to match results from based paper and Ansys Workbench in modeling piezoelectric?

Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...

13 January 2021 7,356 3 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

What is the difference between organic perovskite solar cell and inorganic perovskite solar cell?

Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks

01 January 2021 4,310 6 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

How to call both UMAT and UEL together in Abaqus?

I have a model with bulk material (matrix) and inclusions and cohesive interface elements between both. For the bulk material, I have implemented a UMAT and for the cohesive interface elements, I...

20 February 2021 1,286 2 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm??

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm from the exposed surface in Abaqus... i am performing a coupled...

10 February 2021 4,656 2 View

Recommendations for sample size in visual qualitative research (using children's drawings)?

Hi everyone! Asking for a little help, if I may. I am working on a research project, where I aim to analyse children's drawings about Covid-19. I am fairly new to using visual data in qualitative...

07 February 2021 9,530 3 View

In Abaqus, is it possible to remove elements which are too complex for meshing from a sequence obtained by getByBoundingBox() ?

Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...

03 February 2021 8,198 1 View

Best way to draw COLONY output / pedigrees?

Hi, I am using the sibship analysis software COLONY 2.0.6.6 (most recent version) on about 150 individuals offspring, with some of them as potential fathers and mothers. COLONY provides a lot...

02 February 2021 6,910 2 View

How to plot 3D plot for Measured value of antenna?

Hello everyone, I am trying to plot a 3D pattern from measured data of antenna in the MATLAB, for this, I have many files for one GHz frequency at different theta(e.g theta 90,80,70, etc). My...

31 January 2021 8,458 2 View

Why can't ANSYS Mechanical APDL detect the volume of my design ?

The 1st image shows the moment when I import my design(IGES) into the Mechanical APDL. The 2nd image occurs when I wanted to Operate>Boolean>Divide Volume By Area. The design is a regular...

28 January 2021 2,962 3 View