Dear Colleagues,
In the absence of a standard CC of any size, can improvising using a burette for fractionation (Not purification) give comparable results as when one uses a standard manufactured CC?
What precautions and care-steps should one take?
A burette should do a god job if the amount of support and the ratio support:sample are adequate to make the separation.
Thank you John for your insightful reply.
have a good day
for low volume syringe can also be used
Yes, as long as the burette is packed appropriately.
Thank you colleagues. Your replies are so helpful. Have a good day and kind regards
Andrew
I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...
27 February 2021 1,829 3 View
Remote history of Campylobacter infection with reactive arthritis, and Spitz nevus (UMP). Arthropod exposure in Zika/ChikV endemic area prior to emergence of length dependent, sensory PN with...
18 February 2021 8,719 1 View
I am using Qualtrics for a Delphi survey. Does anyone know if Qualtrics can generate reports that I can send to respondents. More specifically, I want to send respondents a report of their...
13 January 2021 7,976 3 View
Dear Research community, I am writing a review about 2,4-D. Google Scholar has identified 11000 publications with this herbicide as a keyword since 01/01/2018. There is plenty for me to read....
29 December 2020 1,145 6 View
I'm going to be teaching an online course to minors using game-based learning strategies. I wasn't to make sure I consider ethics considering students (likely their parents) will be paying to take...
12 December 2020 6,497 11 View
One of the steps during the preprocessing of the data from metatranscriptomic analysis is to remove any host reads (host contamination) by comparing to host database. But what if there is no host...
30 November 2020 3,259 2 View
Hi, When checking my designed primers for specificity, what is the difference if I run BLASTn for each primer individually versus together (ie. forward primer separated by 20 "N" then reverse...
03 November 2020 1,421 4 View
I am studying the effects on the road system of a rural region of a drastic increase in traffic, particularly Motorhomes. My question is this, do motorhomes and other large vehicles have a...
22 October 2020 8,146 3 View
The molecule in question is a molecule with 3 non-equivalent hydrogens. Am I going to have to run the calculations in all of the transition states?
18 October 2020 1,524 3 View
I have been using Gibson Assembly to insert a 7kB fragment into an 8kB linearized vector. After assembly many colonies form, but colony PCR on the transformation consistently shows a 1.5 kB...
18 September 2020 247 3 View
Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...
03 March 2021 6,299 3 View
03 March 2021 5,360 2 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...
01 March 2021 2,215 2 View
Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...
01 March 2021 2,622 3 View
I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...
28 February 2021 6,477 1 View
I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...
28 February 2021 7,370 3 View
28 February 2021 8,466 2 View
Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...
26 February 2021 3,738 3 View
In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...
26 February 2021 3,806 2 View