Do you know an algorithm for wireless sensor networks using matlab?

More M. K. Bhanarkar's questions See All

If any free simulation tools for NEMS? please suggest it.

RF nems Antenna

05 June 2016 5,819 6 View

Can any body suggest open journal for wireless sensors network?

Open journal for sensors

31 December 2013 448 5 View

Can anybody suggest a perfect simulation software for MEMS?

For better operating results in MEMS.

11 December 2013 6,333 12 View

How can I build up a wireless sensor network to improve grapes cultivation?

To improve crop productivity

09 October 2013 4,609 6 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to sample data to increase presence of solar panels in the images?

I am working on creating deep neural network on geospatial dataset and wanted to know how to do the sampling so that I can increase the presence of solar panels in the images. I cannot use entire...

25 February 2021 3,936 6 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Alexios Lekidis

There is SysWeaver an extension based on Matlab. As far as I know, you can develop and simulate different configurations for sensor networks with it including wireless. I attach the paper you can find it..

Hope it helps..

Conference Paper Model-Based Development of Embedded Systems: The SysWeaver Approach

Afaq Ahmad

Dear Bhanarkar,

You have to match your problem with the available toolbox provided in MATLAB. Also, you may simulate your problem using MATLAB.

M. K. Bhanarkar

Ok, thanks for kind efferts