Do you have the ability to manufacture Schottky diodes with different diameters (5 - 1000 microns) based on metal-Ga2O3 ?

01 January 1970 0 332 Report

Dear Colleague,

Do you have the ability to manufacture Schottky diodes with different diameters (5 - 1000 microns) based on metal-Ga2O3 and measure their correct I-V characteristics in a wide temperature range, where the appearance of an additional electric field is clearly observed?

Badges
Science topic

More Rasim Mamedov's questions See All

How can we simultaneously connect the internal combustion engine and the electric motor to the propeller without loss?

17 January 2020 288 2 View

What should be a hybrid battery with an optimized structure?

What variant of building a hybrid battery would be the most optimal for a drone with a range of up to 50 km and a duration of up to 100 minutes?

21 February 2019 357 1 View

What variant is more effective: Convertoplane or combination of multicopter + aircraft? List reasons?

Convertoplane, this is UAV with turning propeller. Multicopter airplane, this UAV rises as Multicotoker with vertically arranged screws, flying like a plane with the help of a pusher engine...

21 January 2019 1,348 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View