Nimonic 105 is a Nickel-Based Superalloy.
http://bit.ly/18mP3cT
ASM Specialty Handbook Nickel, Cobalt, and Their Alloys Edited by
J. R. Davis
Thank you, I have read ASM Specialty Handbook, but those information weren't important.
What sort of information ARE you looking for?
Hi Seyed, which topic are you looking for? mech props. microstructrure, phases, oxidation, ...
Hi, I am looking for microstructure and TTP diagram of Nimonic 105.
You could directly contact any of the suppliers, e.g. Specialmetals, www.specialmetals.com/ or Outukumpu VDM. Typically, they provide you with a lot of data.
or check out this: http://link.springer.com/article/10.1007%2Fs11663-009-9227-1/fulltext.html
Thank you so much.
Seyed, I could send you the info by e-mail, review my research webpage for contact me.
I installed CCP4 on my PC (Windows 10), but I can't see graphs in Aimless, phaser and also, Refmac5 is not able to open Coot directly itself. Does anyone experience the same issue? Any...
24 October 2022 7,996 0 View
I am performing an assay on my adherent cells and up until the day of the experiment, the cells grow nicely and reach a good confluency of ~ 80 % cell density. However, on the day of the...
21 June 2021 913 5 View
I am using two REs enzyme (EcoRI and NdeI) to cut my plasmid. At first, I used two enzyme together and one of them did not worked. By an initial search, I found that it is a common problem and if...
11 November 2020 4,186 3 View
I would like to know what is the best software to model water absorption of a brick masonry? Which one of CFD or HAM theoretical aspects must be taken into account? Actually, in our experimental...
01 January 1970 9,305 4 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,988 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 453 3 View
I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...
02 August 2024 2,890 0 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,713 4 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View
I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...
21 July 2024 1,559 1 View
I am using gelatin to model mechanical properties of brain tissues in-vitro. Do you have any suggested concentration ? Thank you so much.
19 July 2024 3,095 0 View