Do conductors have band gap? Then how will someone describe the band gap in conducting polymers?
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...
31 July 2024 2,033 1 View
Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.
25 July 2024 7,498 2 View
In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....
24 July 2024 8,076 3 View
Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?
21 July 2024 7,545 0 View
I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.
18 July 2024 4,218 0 View
I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.
17 July 2024 5,633 4 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
im studing gaussian 16 with reading paper about I-131 Metaiodobenzylguanidine in the paper "In a similar vein, nuclear magnetic resonance shielding values were investigated using the widely...
16 July 2024 6,040 4 View
I am doing a systematic review, and I am measuring risk of bias with RoB2 for RCT, and ROBINS-I for non RCT. My questions is, for single arm studies, can I use ROBINS-I? I am not sure how to...
14 July 2024 3,570 5 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...
30 July 2024 8,339 2 View
Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.
29 July 2024 6,350 3 View
Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...
25 July 2024 2,920 11 View
Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.
21 July 2024 3,045 3 View
I want to calculate the spin texture for the electronic band structure obtained from SOC calculation. Is there any way for calculation of spin texture using quantum espresso??
19 July 2024 8,571 1 View
For which types of polymers, the crystallization peak in heating cycle of DSC test can be observed and for which types cant? In another word, when this exothermic crystallization can be observed...
18 July 2024 348 3 View
Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...
18 July 2024 7,258 3 View
I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...
16 July 2024 5,031 1 View
We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...
12 July 2024 2,768 1 View