Design standard for concrete pavement tie bar?

More Amjad Albayati's questions See All

Micro, Meso and Macro?

what is the difference between Meso, Micro and Macroscopic analysis method..?

02 March 2017 3,735 5 View

Polythene Sheeting in Rigid Pavement?

What is the function of a separation membrane between concrete pavement slab and sub-base?

02 March 2017 1,884 4 View

Bituminous surfacing over concrete?

What is the purpose of paving bituminous surfacing over concretestructures?

02 March 2017 3,446 10 View

Rigid Pavement Construction?

For rigid pavement, what are the advantages of using lean concrete sub-baseinstead of traditional granular sub-base?

02 March 2017 497 2 View

Plain Concrete Rigid Pavement?

For unreinforced concrete carriageway, what is the sequence of closing andopening of expansion joints and contraction joints?

02 March 2017 2,392 4 View

Subbase Granular Material?

What is the significance of ten percent fines value in testingsub-base material?

02 March 2017 9,841 2 View

Regression Analysis in Statistic?

what is the difference between t statistic and F statistic in the linear regression analysis?

02 March 2017 2,301 3 View

Rigid pavement expansion joint?

If the construction of concrete carriageway is carried out in summer, canexpansion joints be omitted?

02 March 2017 4,818 3 View

Moisture Susceptibility of Asphalt Concrete?

what is the best anti stripping additives to reduce moisture damage in asphalt concrete?

02 March 2017 7,668 5 View

Asphalt Concrete Performance (Fatigue)?

what is the difference between the occurrence reasons of thermal fatigue cracking and fatigue cracking?

02 March 2017 7,818 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View