Dear professors and colleagues, a blue spot develops on tlc which is seen in visivble light, but once i spray with anisaldehyde, heat it disappears?

More Samar Bassam Moaz's questions See All

Does anyone have this article: the morphology and anatomy of. Yucca L. Ph.D. thesis, Univ. of Calif., Berkeley. . 1962.?

i need it desperately. thank you so much

31 December 2018 1,765 4 View

Are we supposed to have the same type of adducts for all peaks in ms spectra?

Dear ms experts is it possible to get some M+ ions, some M+ H, some M + 2H FOR different component in an extract but during the same run

09 October 2018 9,831 0 View

Is there a lab in Egypt which has counter-current chromatography device?

I need counter current technique to separate very close compounds

08 September 2016 5,805 2 View

Should a plant extract be dissolved in DMF or DMSO only for antimicrobial assay?

the extract dissolved in ethyl alcohol gave negative results...could it be due to poor diffusion to agar?

09 October 2015 2,471 10 View

Please can anyone send me the AOAC 2007 method for total phenolic content?

OFFicial methods of analysis of AOAC international. 18 th edition ..2007

07 August 2015 4,336 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

In an eye with Tyndall, does each dot correspond to an individual cell?

When you observe the presence of Tyndall in an inflamed eye: Does each of the small floating dots correspond to an individual cell or to an aggregate of cells? Does a conventional slit lamp have...

27 February 2021 6,326 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View