Could someone please suggest what type of stabilization ( Steric, electrostatic or Electrosteric) in Zirconia and alumina composite happens ?

05 May 2016 0 4K Report

Could someone please suggest what type of stabilization ( Steric, electrostatic or Electrosteric) in Zirconia and alumina composite happens while citric acid is used as dispersant and the solution environment is alkaline. Could you also advise what mechanism is happening during stabilization?

Badges
Science topic

More Sami Tehrani's questions See All

Are there any disadvantages for using reciprocating wear test in high speed?

Please could someone advise if there are any disadvantages while using reciprocating wear test at high speed around 10 HZ in terms of COF. Is there any possibility that the system cannot read the...

11 December 2016 1,012 9 View

How can I interpret the Raman spectra of alumina and 3Y-TZP?

I have a Raman Spectra of Alumina and 3Y-TZP sintered around 1500 C. The Raman Spectra is showing few small peaks above 1000 cm-1 and one peak around 1650 cm-1. As most literature does not...

10 November 2016 5,537 2 View

Please could someone suggest why the samples which have been processed in exactly the same way obtain different colour after sintering by SPS?

Please could someone suggest what are the possible reasons that the samples (Alumina and zirconia) which have been processed in exactly the same way ( Ceramics Processing and also the same recipe...

31 December 2015 6,417 7 View

Does anyone know why the surface of SPSed (Spark Plasma Sintering) Samples are rougher than pressureless sintered Samples?

Please could you help me to understand about main reasons that make surface of Spsed samples rougher than pressureless samples?

10 November 2015 831 5 View

The shrinkage rate Vs temperature graph shows two peaks at different temp. Would it cause a problem for sintering and densifying processes?

I have two different phases in my composite which are Alumina and Zirconia. The shrinkage rate Vs temperature graph shows two peaks at different temperature. I am not sure if two different max...

03 April 2015 4,978 4 View

Has anyone ever had the experience of having bumpy surface after making a zirconia /Alumina sample by SPS followed by thermal etch?

After making composite out of zirconia and alumina by SPS followed by grinding, polishing and thermal etch, my samples get bumps over surface. I'm not sure about the possible reasons. Please see...

02 March 2015 7,690 5 View

Why do researchers mix strontium carbonate with Alumina to form strontium hexaluminate rather than directly mixing strontium oxide and alumina?

I see in publications that people don't directly use strontium oxide to react with Alumina and instead they use other derivatives of Strontium such as Strontium carbonate to form strontium...

02 March 2015 3,089 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

The aqueous fraction of the hydroethanolic extract is showing the presence of palmitic acid. What is the mechanism responsible ?

Palmitic acid presence in aqueous fraction

05 August 2024 8,624 4 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

How to convert g/kg Humic acid dose to kg/ha?

I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?

02 August 2024 7,186 6 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View