could any body offer a source for knowing the mechanism of glass corrosion in contacting the alkaline aqueous like NaOH ?
Attached are couple documents on "Theory of Corrosion of Glass"
Hope they will help
http://ufdcimages.uflib.ufl.edu/UF/00/09/91/34/00001/mechanismskineti00ethr.pdf
http://www.semos.dk/Per/41653/download/Korrosion%20af%20glas%20og%20keramik.pdf
Since the major contributor of glasses is silicon dioxide, the hydroxide attacks the Si to form soluble silicates. Here is a detailed study on many factors of glass corrosion: http://www.ceramics-silikaty.cz/2010/pdf/2010_03_235.pdf
Hello everyone. I am looking for the grid points of grain boundaries(blue sections).Is there a way to aciheve them by image processing in Matlab?. Thanks.
11 December 2019 4,460 10 View
Hello. Is there a way to count the total number of grains in an image using the average diameter? Thanks.
11 December 2019 662 2 View
I am running the attached code. it is about the grain growth using phase field model. But unfortunately its performance in high grid point is not good enough. one the algorithm that is common for...
11 December 2019 1,372 1 View
Hi. I'm working on annealing of Al5083 and need to anneal that in salt bath. The temperature range of my experiments are between 200-500. I'd be appreciate to receive the name of proper salt for...
03 April 2019 4,413 1 View
I'm studying the phase field method in SRX. In mots of literature, the grain boundary mobility and others parameters are dimensionless but it is not mentioned the proper characteristic value for...
09 October 2018 3,447 0 View
I'm implementing the phase field model for dynamic re crystallization. In the Multiple phase field model, I faced two parameter "phase field mobility " and "grain boundary mobility"!. Let me know...
09 October 2018 4,718 0 View
Hello, I'm trying to implement and reform the codes which has been written in the book of Programming phase field book of Bulent. In this book the parameters such as grain boundary mobility is...
03 April 2018 8,052 0 View
Hello, I need the solution manual of Theory of plasticity Chakrabarty. But unfortunately this source is not free in the net. I'd be appreciate if anyone shares this source for me.
01 February 2018 7,403 4 View
I am working on micro structure evolution. I didn't t find any useful sources on modeling and programming the recrystallization by phase field mothod. I would be appreciate if anyone can give me...
11 December 2017 814 5 View
could anyone offer any useful sources about the effect of electrical conductivity of acidic and alkaline electrolytes on dissolution of glass ?
05 June 2016 7,327 0 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?
08 August 2024 8,915 0 View
In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...
25 July 2024 7,982 3 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...
10 July 2024 2,937 3 View
Would anyone be interested in collaborating on corrosion?
07 July 2024 4,726 2 View
Hi all, I am looking glass cilinders that have an open flat bottom and top. Preferably with the inner diameter in the range of 2 cm. It's similar to the ones found on multi-electrode arrays for...
06 July 2024 5,846 1 View
If we want to introduce a material similar to polymethyl methacrylate "with the characteristics mentioned in the next paragraph" that can be added to a precursor and create a composite, which...
03 July 2024 2,371 1 View
I use PDMS to build a microfluidic system, but it is not hardening at all, although I use TEOS as a cross-linker and also ATPES in a ratio of 1:10, and it's been 3 days at 80 degrees of 3 ml cast...
01 July 2024 604 3 View
we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...
30 June 2024 5,943 2 View