Composition and mechanical properties of experimental alloys?

More Shivraj SINGH Kasana's questions See All

What microstructural and physical changes will happen if high hardenability steel sample after quenching is kept for self aging for six months?

To study the effect of self aging in low alloy medium carbon steels and high chromium air hardening martensitic stainless steels, various steel grade samples are under study in my research...

06 July 2019 6,949 7 View

How we can determine critical temperatures like ac1,ac3,Ms Mf and liquidus temperature of a steel alloy by thermo mechanical simulator?

In my experimental alloy I want to calculate the actual critical temperatures of alloy steel like ac1.ac3.Bs. Bf, Ms,Mf,liquidus and solidus temperature by TMS GLEEBLE 3800.This will help me in...

04 May 2018 2,500 8 View

Upto what minimum grain diameter we can achieve by severe plastic deformation in ultra high strength steels?

I wish to utilize all possible strengthening mechanism in developing a unique ultra high strength nano bainitic steel

04 May 2018 8,292 2 View

How much time journal of Materials processing and technology takes to publish a paper?

Is is about publishing a paper in suitable journals

03 April 2018 2,129 2 View

How to prevent microstructural banding in medium carbon nickel chrome moly low alloy steels?

Severe microstructural banding is observed in HSLA nickel ,chrome moly steel rolled bars which is not removed by hardening and tempering. and results in poor high cycle fatigue properties.This is...

03 April 2018 2,064 1 View

In which countries people celebrate festival of colours called HOLI like in India?

Holi the festival of playing with colours with each other is played in India .BARSANA a plce near Mathura is famous for Lath maar holi from radha-krishna times.HAPPY HOLI TO all fellow researchers...

02 March 2018 6,239 0 View

We are using HHA steel plate with hard armor and soft armor panels to resist ballistic test by hard steel core projectile can someone tell is it ok?

In construction of bullet proof jacket 600 BHN quenched and tempered low alloy UHSS steel sheet of 3mm thickness is used in strike face followed by HAP and SAP made by high density polyethelene...

01 February 2018 7,911 0 View

If warm bending of high hardness armor sheets are bended ,can some body tell how much time plates should be heated before warm bending?

Required for my project

31 December 2017 10,012 2 View

When calculating Ms and Bs temperature of an hypereutectoid low alloy steel Ifound that Ms and Bf temperatures are different why so?

In absence of dilatometer and other facilities I wish to estimate my heat treatment temperature by emperical formulae available but find difference of about 84 deg.C in Bf and Ms,what should Ido?

31 December 2017 2,886 0 View

How we can improve weld properties and reduce HAZ in welding of high hardness armor steel plates?

Since fabrication by bending and welding is required in construction of armor protection structures made from high hardness ultra high strength armor steels a thorough understanding of these...

31 December 2017 3,592 4 View

Why do men not accept that continually hassling for sex proves that they want it more than their partner?

Your partner’s not there to service you, it’s not their job to keep you sexually satisfied. You’re together because you love each other and want to make each other happy. Constantly hassling them...

08 August 2024 1,491 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

I am considering injecting cisplatin directly into an equine sarcoid tumour that is chronically refractive?

My case has been under treatment now for 3 years with little response. Now considering euthanasia. Last ditch is Cisplatin for dilution in iv infusion (100ml/ml in saline and mannitol). What can I...

05 August 2024 1,835 0 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

What is the best method to detect the chemical composition of pollen ?

I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?

28 July 2024 5,331 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Linto George Thomas

Hi, can you provide which experimental alloy

Below article might be helpful for you

Haydar Al-Ethari

Can you explain what is your problem exactly?

Adin Stern

Hi, I would suggest to use Prof Ashby's books on Materials Selection for

some general answers and examples. For specific problems you should search the literature; see the answer you got from Dr L G Thomas.

GOOD LUCK.