Can you share Fluid Mechanics ( UG Course) assignment?

Sachin Arvind Mandavgane @Sachin-Mandavgane

20 September 2017 0 7K Report

I am looking for Fluid Mechanics assignments designed based on Real Life situation.

Badges
Science topic

More Sachin Arvind Mandavgane's questions See All

How to make graphene oxide film on substrate for electrochemical performance?

I am trying to deposit graphene oxide film on steel electrode via drop casting (Electrochemical synthesis of layer-by-layer reduced graphene... ) and dry it in oven at 60 C. when i put this into...

04 December 2020 820 2 View

If anyone can suggest or review manuscript having keywords Riparian zone, River, Species richness, Species evenness, Ornithofauna?

Greetings I am Sachin Kumar, pursuing my Ph.D. in Ornithology, from PAU, Ludhiana. I am working on avian diversity along the River Beas. I had submitted a manuscript to a journal having keywords...

10 November 2020 7,194 6 View

Can anyone provide me .pdb file for Spike protein of SARS Cov-2, ACE2 complex and TMPRSS2?

Dear Research Colleagues, I am looking for the .pdb file for Spike protein of SARS Cov-2, ACE2 complex and TMPRSS2. I have to use them for Molecular Docking analysis of synthetic organic compounds...

08 September 2020 8,788 3 View

Can i use Ag/AgCl reference electrode to electrodeposite silver?

I'm trying to electrodeposit silver nanoparticle from aqueous solution of AgNO3 via three electrode configuration. When i dip three electrode in aqueous AgNO3 solution, a whitish fluid coming out...

22 August 2020 6,837 7 View

Can i use Graphite flakes having 325 mesh particle size instead of Carbon Black or acetylene to make slurry for electrochemical performance ?

Can i use Graphite flakes having 325 mesh particle size as conductive agent instead of acetylene black or carbon black to make slurry for super capacitor electrode ?

27 July 2020 1,176 1 View

Why bubbles appear on film during Galvaostatic charging discharging?

I electrodeposited GO/PANI directly on electrode and dried at room temperature, then used it for Galvanostatic charge discharge via three electrode configuration in 1 M H2SO4. During charging...

20 July 2020 5,988 8 View

Is it necessary to do Open circuit potential before CV, Galvanostatic charge discharge and EIS for Supercapacitor electrode?

for electrochemical performance of supercapacitor electrode i am doing CV, Galvanostatic charge discharge and Potentiostatic EIS via three electrode configuration. is it necessary to do open...

19 June 2020 2,026 7 View

Does metal to metal joining by FSW really occur so as to withstand loads in abaqus?

I am curious to know if metal bonding by welding (FSW) can really be simulated in Abaqus or not. I have read many papers wherein people simulate the FSW process only and study the temperature and...

15 June 2020 6,471 1 View

Which is correct formula to calculate gravimetric specific capacitance from Galvanostatic charge discharge method?

I have to calculate specific capacitance (F/g) from galvanostatic charge discharge. in electrochemical test, one is working electrode, platinum sheet as counter electrode and Ag/AgCl as reference...

07 June 2020 5,213 3 View

How to develop 3D setup for abrasive jet machining in ansys fluent ?

hello everyone....... I am trying to develop 3D setup of abrasive jet machining (AJM) which consist of nozzle from which stream of air+abrasive (two phase flow) strike the workpiece and erosion...

30 May 2020 2,136 8 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View