Can we process gnss data for different cutoff angles and get it as a rinex file as output?
Yes, you can using leica Geo office or leica infinity, after processing you can get as rnx2 or rnx3. You can process them using Bernese V.5.2 software will give you output with precise RMS but the output not rnx file.
I recently did some calcination (500C) on a hydrated powder material in three sets of experiments. The experiments only differ in the moisture content of the calciner i.e. 0, 40 and 80%. Then I...
24 January 2024 7,291 0 View
Hello everyone. i want to place a landing beam without connecting the column. The landing beam will complete rest on brick wall of 230MM thick wall of height 1.5M from floor beam. How can I check...
02 December 2023 2,692 0 View
I want parameter for carbonation (CaO+CO2 to get CaCO3)in low temperature the highest temperature is 450 c with out stirring i want to do this experiment in co2 capture and this instrument only...
10 November 2023 2,064 2 View
looking for a method for detection the artificial coloring agent in honey sample? like E133, E102, E120 ....
20 June 2023 6,778 4 View
I wanted to start using pooled HUVECs in my expirements to reduce the possible variations in cell phenotype and behavior due to the different genetic background of donors, but I'm not sure about...
27 February 2023 3,612 0 View
Dear scholars, is Middle East Journal of Applied Sciences a good journal to publish a paper?
22 February 2023 3,882 0 View
Regarding the clay minerals, what is the phase of alumina? delta, gamma, theta or alpha? In a separate question, what occurs to this phase after calcination at around 800 C?
16 October 2022 5,560 7 View
Hi, I am using materials studio for Ti3C2 and the universal forcefield. Unfortunately, msi2lmp does not support universal force field class. Do you have any suggestions to obtain a data file for...
21 June 2022 5,500 1 View
Plz answer me few queries my Project work z synthesis of metal doped acacia Arabia mediated cuo nanocompsites along with gold coating 1.why gold coating is given to nanocompsites 2.whats...
26 October 2021 1,243 8 View
I understand, that melts of ultamafic and alkali lammprophyres must be lower, than kimberlitic speed, because the number of xenoliths and xenocrysts is lower compared to kimberlites. But i...
16 September 2021 1,359 2 View
The paper in question is "Interpolation of Nitrogen Fertilizer Use in Canada from Fertilizer Use Surveys". This paper was very recently published by Agronomy (MDPI). Agronomy has, in the last day...
07 August 2024 9,934 3 View
Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out
07 August 2024 6,066 0 View
The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.
07 August 2024 9,508 1 View
Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...
06 August 2024 4,953 0 View
Dear Researchers Kindly share JCPDS 65-7246 file Thanks in advance
04 August 2024 5,613 1 View
Hi everyone I need a file with a dirty and clean potato image
04 August 2024 7,199 4 View
How to change the displayed full article text to its corrected version? In the file on the page of the journal where I published the article, there was an error in the text, the table is...
30 July 2024 3,229 2 View
Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...
30 July 2024 5,206 1 View
i m interested in pca analysis of c-alpha atoms in gromacs for that i used the following gmx_mpi covar -s mdca.tpr -f mdca.xtc -o eigenvalca.xvg -v eigenvecca.trr -av average.pdb -n index.ndx but...
30 July 2024 1,607 1 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View