How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

Data Analysis K-S and S-W tests?

Hello, I have conducted analysis where the K-W and S-W have come out as p

25 February 2021 9,648 3 View