Can two xbee RFX240 modules be configured using XCTU?

30 May 2018 1 6K Report

I am trying to create mesh network using zigbee technology . For the same, I have with me four xbee RFX240 modules. But the modules are not being detected by XCTU . So , is it posible to configure them using XCTU?

Dinesh R. Gawade

i think no, you can't configured xbee RFX240 using xctu because xctu tool for only Digi International Inc products. you can only configured Digi International Inc products using xctu. if manufactured of xbee RFX240 is not Digi International Inc then it is impossible to configured it using XCTU.

Badges
Science topic

More Raasi Chenna's questions See All

Can a heat transfer process be internally reversible?

A system undergoing heat transfer can be brought back to its initial state using refrigeraion.Here refrigeration leaves a trace in the surroundings but not in the system. Then why heat transfer...

31 August 2018 9,332 2 View

Can anyone plz share the download like for Advanced design system( ADS) ..?

can anyone plz share the download like for Advanced design system( ADS) which can be downloaded freely and installed in my laptop without any problem. This will helps me more in my work .

19 July 2018 3,782 1 View

Can you tell me, what are the different parameters need to consider to design an antenna using HFSS.

can you tell me, what are the different parameters need to consider to design an antenna using HFSS.

24 July 2017 6,663 6 View

Request for help in phd work- Microtrip antennas( HFSS & CTS Related)

Greeting of the day!!!!! Dear sir, I p c praveen kumar pursuing phd in RF &Microwave communications with the title tunable inverted L antenna with double folded arm using split...

13 July 2017 366 6 View

Is there any literature on ground motion studies of the 2002 Denali earthquake?

Hello, During the 2002 Denali earthquake, a maximum horizontal slip occurred on Denali fault, which is about 150 km from the epicenter of the earthquake. The maximum recorded PGA was 0.32 g at...

20 October 2015 4,777 5 View

Is the slip of the fault considered in synthetic accelerograms?

Hello, I am using semi-empirical approach to generate synthetic ground motion. This approach is a combination of Empirical Greens function and Stochastic Simulation methods. This method doesn't...

11 October 2015 8,944 6 View

Are sythetic accelerogram and artificial accelerogram same?

Hello, I need a small clarification on artificial and synthetic accelerograms. To my knowledge, synthetic accelerograms are those which can be derived from seismological parameters and artificial...

29 September 2015 6,111 6 View

How can I fix the range of frequencies to determine kappa parameter from Fourier Amplitude Spectrum?

I need a small clarification regarding finding out kappa parameter. From an engineering point of view, the value of kappa parameter can be calculated from the slope of Fourier amplitude spectrum...

02 January 2015 6,497 4 View

Which software tools are best for enhancing diagnostic accuracy in chest X-ray imaging using image reconstruction and neural networks?

I am reaching out to seek your valuable advice and recommendations regarding the best software tools to use for this research. Specifically, I am looking for software with a user-friendly...

22 July 2024 3,794 1 View

How can I extract the mathematical equation from existing Neural Network Model?

There exists a neural network model designed to predict a specific output, detailed in a published article. The model comprises 14 inputs, each normalized with minimum and maximum parameters...

14 July 2024 2,714 3 View

What is the current status of augmented learning in robotic surgery?

I would like to perform a literature review at this time on augmented learning and learning augmented algorithms to enhance performance-guided surgery

06 July 2024 246 1 View

The value of RF3(Z) in Abaqus model is huge how to control that?

I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...

27 June 2024 4,212 2 View

Is it possible to use neural network models for prediction if the sample size for the time series is very small??

Forecasting within neural Network

24 June 2024 6,800 1 View

What is information diffusion in the social network?How a message got viral in social network?

Please give answer. Also explain mathematical equations behind this.

22 June 2024 6,869 2 View

In CNN, is the feature map obtained randomly by convolution kernel?

In CNN(convolution neural network), can the feature map obtained determinately by a random initialization convolution kernel? if not, how to decide the weights in convolution kernel to obtain the...

20 June 2024 6,418 6 View

How does a Man-in-the-Middle (MitM) attack work in the context of Transport Layer Security (TLS), and what specific mechanisms can be employed ?

Context In the realm of cybersecurity, Transport Layer Security (TLS) is widely used to secure communications over a computer network. Despite its robust encryption mechanisms, TLS is still...

19 June 2024 6,595 3 View

Can someone introduce an article about the convergence of the temperature parameter for the SPH part in Abaqus software?

For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...

13 June 2024 2,504 0 View

Can we use SHAP values to explain the performance of a Neural Network ?

Can SHAPELY (SHAP) values be used to explain the importance of different features being fed to a Neural Network ? I know they are used in Traditional ML on Tabular data

10 June 2024 2,054 2 View