Can the flying capacitor topology be used to build a 400hz inverter?

09 December 2021 0 4K Report

can the flying capacitor topology be used to build a 400hz inverter?in terms of THD and high output signal quality?

Badges
Science topic

More Reza Kam's questions See All

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to model Type 1 collagen structure for finite element analysis ?

I have started a project in which stress distribution in Type 1-collagen scaffold is to be modelled. I am thinking of using finite element analysis to model the structure and the loading...

07 February 2021 5,487 3 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

How can I model a vacuum region between a concentric tube in Ansys fluent?

I am modeling a double pipe (concentric tube) in Ansys Fluent. The center tube contains nanofluid, and the region between the pipes is a vacuum zone. The outer tube is used for reducing convection...

22 January 2021 2,781 3 View

What type of plants is better to work in gene regulation control project ?

I Interested in to work in gene network modeling thus I need to know what is future of gene network modeling in agriculture thanks

04 January 2021 6,527 3 View

Is it possible to culture several cell lines in the same plate/dish/flask with complete cell separation?

I'm trying to screen the effect of a toxic agent. I need to see its effect on a few different cell lines with different degrees of resistance to this compound. I would like to possibly culture...

31 December 2020 5,740 3 View

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 2,109 5 View

How to find the natural frequency of nonlinear model (hyperelastic materials) in ansys APDL?

I'm working on the FE analysis of nonlinear vibration of circular plate in ansys APDL. I considered the Mooney-Rivlin model of hyperelastic materials. So i want to know that how to find natural...

27 December 2020 8,696 2 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Can I consider the OOB score of RF model as the same as R^2 score?

In a topology optimization machine learning prediction algorithm, can I consider the OOB score of RF as the same as R^2 score. Could that be a more unbiased way of validating the model

14 February 2021 3,540 1 View

Charmm/GROMACS Residue 'ZN' not found in residue topology database?

I am trying to do some MD simulations of a protein with zinc ions. I am trying to use a charmm forcefield (I have tried 2017 and 2021) and Gromacs. I get an error when doing pdb2gmx Residue 'ZN'...

12 February 2021 9,367 2 View

Grid connected inverter using virtual synchronous machine?

Hi everybody, currently, I am working on the grid-connected inverter. I want to make my grid-connected PV system a PLL-less system. I have studied some reachers are implementing a virtual...

07 February 2021 6,078 2 View

Do anyone have a full MATLAB code for structural topology optimization using Genetic Algorithm? Such as a cantilever beam?

Do anyone have a full MATLAB code for structural topology optimization using Genetic Algorithm? Such as a cantilever beam? Could you provide some MATLAB code to me , a beginner for GA. Thank...

03 February 2021 3,789 5 View

Matrix based scientific data analysis: extrapolating to matrices of sets?

Data sets, when structured, can be put in vector form (v(1)...v(n)), adding time dependency it's v(i, t) for i=1...n and t=1...T. Then we have a matrix of terms v(i, j)... Matrices are important,...

30 January 2021 9,295 6 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View

Can't generate a mash for topology in ANSYS. how to do it?

Created model of steel caisson in space claim. Used a static structure for topology. But there's an error "one or more surfaces cannot be mashed with acceptable quality", " One or more entities...

25 January 2021 893 1 View

Can anyone suggest which type of sensor input signals are more critical in flying aero engines for on-board diagnostics?

Can anyone suggest which type of sensor input signals are more critical in flying aero engines for on-board diagnostics? and high potential sensors for prognostics?

18 January 2021 4,087 1 View

I am facing problem with integration of boost converter with single phase offgrid inverter?

i tested boost converter with MPPT and single phase offgrid inverter with close loop control separately. They work fine but when i connect them boost converter doesn't give the output as it did...

17 January 2021 6,428 6 View