I have been measuring photosynthesis in mosses that have been desiccated and then rehydrated and comparing it to non-desiccated mosses. I am using a modified Wisconsin fast plant technique to measure desiccation and have gotten various results.
When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...
28 February 2021 2,133 3 View
We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...
28 February 2021 1,149 1 View
Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...
22 February 2021 1,115 4 View
In my opinion, the RG site is useful in solving scientific problems and shows the researcher's ability. Besides, the separation of the H-index from the self-citations and the overall index is an...
22 February 2021 3,894 6 View
Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...
22 February 2021 3,680 4 View
I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...
20 February 2021 3,950 15 View
the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please
16 February 2021 8,801 3 View
We collected faecal samples from various species that we want to analyse their microbial communities' DNA via Next-Generation Sequencing. The problem is that due to budgetary constraints, we will...
16 February 2021 5,466 4 View
When you use RNAseq I understand that it must follow certain conditions when you use it. One of them is the insertion of a polyA tail. The insertion of the polyA must include then...
05 February 2021 3,770 4 View
Dear all, I am trying to optimize a bimetallic complex using # opt=tight b3lyp/lanl2dz scf=qc geom=connectivity. The program is running for around 5 days but the size of the .chk remains same...
05 February 2021 8,721 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....
02 March 2021 7,890 2 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...
01 March 2021 8,235 2 View
during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...
01 March 2021 7,476 4 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...
27 February 2021 5,681 3 View
Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...
26 February 2021 8,399 5 View