The Laaksonen and Kulmala model (L-K model) relates the surface tension of binary liquid mixtures to the interfacial volume and mole fraction. Can this model extended to ternary or multi-component liquid mixtures?
Could it be that this is already done, see link.
@ Ger Koper: thanks. what is this link?
I downloaded the manuscript, link does not persist ...
It is known that the surface/interfacial tension tension can be measured by pendant drop method and the following equation: IFT=deltaro*g*de^2/H. 1/H is function of ds/de (1/H=f(ds/de)). I used...
01 February 2018 5,919 10 View
It is known that the solubility of sulfur dioxide and hydrogen cyanide in water is high (higher than H2S). Is ionization of sulfur dioxide and hydrogen cyanide in water significant?
03 April 2017 1,100 6 View
I have modeled the surface tension of tetrahydrofuran (THF)/2-propanol mixture at T=288.15 K (xTHF=0.55) by using gradient theory. I take tetrahydrofuran (THF) as a reference fluid. The density...
08 September 2016 5,104 1 View
I search for equation for describing the fugacity coefficient of surface phase or interface because I believe that different equation is needed for surface phase or interface. I search for the...
02 March 2016 9,968 5 View
The interfacial tension usually decreases by increasing pressure, but for water/immiscible liquid interfacial tension increases by increasing pressure.
02 March 2015 4,511 3 View
The solubility of liquid octane in water decreases by increasing the pressure of system at constant temperature although it is expected that solubility of liquid octane in water increases by...
02 March 2015 3,704 10 View
I search for a book in which the thermodynamics of interfaces is well explained.
02 March 2015 5,832 14 View
I do calculations with sPC-SAFT EOS for CO2/H2O system. It performed good for liquid but the results of vapor phase were not good.
11 December 2014 8,029 6 View
It is known that many viscosity and thermal conductivity models are only applicable for atmospheric and saturation conditions. On the other hand, very high pressures (higher than 500 bar) is a...
01 January 1970 8,714 3 View
In thermodynamics, it is known that residual properties show how much a mixture deviates from the ideal state. Do we have other criteria for this? Do we have any criteria by which we can recognize...
01 January 1970 6,808 2 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...
06 August 2024 4,611 0 View
I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...
06 August 2024 662 1 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?
01 August 2024 1,722 1 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...
29 July 2024 5,015 1 View
I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?
28 July 2024 5,331 1 View
In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?
28 July 2024 2,988 0 View