Can I get any study materials about " Secondary processing and joining of composite" ?

More Sanjay M R's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

Cloning of flaviviruses is difficult i have noticed that cells loose their transformation ability after cloning fragments inside vector any advice?

As flaviviruses genome is very frequently prone to mutation hence it is very difficult to clone whole genome inside vector what kind of vector and cells can sustain such amount of cloning...

11 July 2024 4,284 0 View

I am not getting proper colonies while ligating one of fragments in my vector the colonies seems to be normal but in light it seems lysed any reason?

I am working on cloning of a gene fragment inside my vector everything we tried to do correctly like making insert and vector with utmost care but after ligation the morphology of colonies seems...

11 July 2024 9,010 3 View

Possible reasons for not getting wake effects in free surface?

Hi, I am trying to simulate a ship in a canal. The top width of the canal is 20m, bottom width is 6m, depth is less than 5m. Ship has a length of 11.7m breadth of 4m, draft is 0.62m. The velocity...

10 July 2024 1,732 4 View

Do I need specific antibodies to stain for a fusion protein?

I am staining some brain sections stored in cryoprotectant that express a Histone H2B- GFP fusion protein that were generated ~10 years ago. I know I need to enhance signal with an anti-GFP...

07 August 2024 5,338 2 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

What is the function of fusion tag GAMGSGIQRPTST?

I found that several expression constructs of published protein structures containing an N-teiminal fusion tag GAMGSGIQRPTST. What's the founction of this fusion tag?

23 July 2024 1,353 4 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

How can get paper ?

I need a copy of the research titled “An Efficient Automated Multi-Modal Cyberbullying Detection Using Decision Fusion Classifier on Social Media Platforms" An efficient automated multi-modal...

08 July 2024 7,381 3 View

How to calculate corrosion rate from potentiodynamic polarization test data for dissimilar welds?

we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...

30 June 2024 5,943 2 View

How to predict Protein structure and choose N or C terminal tagging?

Hi, may I know I want to fuse my protein with affinity tag for protein purification in Expi293, how can I determine and visualise how does a N or C terminal tag affect my proteins (structure,...

24 June 2024 8,622 6 View

I am modelling resistance spot welding (2d) in comsol, so how to get nugget formation ?

I am using apparent heat method for simulation

14 June 2024 4,670 1 View

How do integrate ECG, PCG, and clinical data to apply early fusion multimodal?

how do integrate ECG, PCG, and clinical data to apply early fusion multimodal?

10 June 2024 3,289 1 View

Analysis of Tensile Test Results Without Using an Extensometer?

I conducted a tensile test to analyze the strength of a welded joint and to implement an FEM model. Due to the high hardness of the base material, slippage between the grip and the base material...

10 June 2024 5,736 6 View

Mikhail Slobodyan

You can try to find here https://www.intechopen.com/search?q=composites