How we control humidity in gas sensor?

Is humidity introduce when Ar/N2 is used as carrier gas in gas sensor?

05 June 2017 9,630 0 View

Please suggest me supplier or labs where i get CNTs/Si junctions based substrate?

02 March 2017 4,466 0 View

Can anyone guide me about air brush technique to deposit the film of CNTs?

Which type of gun/air brush required for this?

09 October 2016 4,877 5 View

Can anyone tell me, which solvent is required for CNTs thin film deposition by spin coater?

Generally, CNTs has poor adhesion on Si wafer, when deposit their thin filmby spin coater. So, I need a solvent that help in good adhesion of CNTs by spin coater...

09 October 2016 6,297 7 View

Can anyone suggest me, order of defect density in case of Graphene using Raman Spectrum?

In my case it comes 5e19cm-2... its very large as compared to reported values....

08 September 2016 4,531 0 View

Can anyone suggest me, how we calculate electrical band gap of CNTs?

Any appropriate technique specially for MWCNTs?

07 August 2016 2,499 2 View

Can anyone suggest me approximately value of electrical current in CNT/Pani Compoites?

with concentration of CNTs in polymer?

07 August 2016 9,405 3 View

Can any one suggest me, which type of sensors used to detect amount of, Chlorine, chloramine, Pb, VOC in water?

05 June 2016 2,330 2 View

Can any tell me, why resistance decrease as temperatures increase in case of MWCNTs?

generally, MWCNTs behave as semiconductor at room temperature.. in my case at room temperature, its i-v is perfect ohmic, but when we record i-v with temperatures.. i found that its resistance is...

04 May 2016 4,421 9 View

Can any one tell me, why electrical current is improved by the addition of CNTs in polymer matrix?

04 May 2016 9,886 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View