Can anyone suggest the process parameters involved in manufacturing of Al-Li water reactive powders?

More Pranjal Chauhan's questions See All

Which one is best theoritical model that takes account interfacial thermal resistance while predicting thermal conductivity fiber/polymer composites?

Hello Everyone, I want to know about best analytical model that consider the interfacial thermal resistance which predicting the thermal conductivity for fiber/matrix composites. Here, Best...

30 December 2020 6,375 2 View

Sample does no retain in the well while doing NATIVE Gel electrophoresis?

While doing NATIVE-Gel electrophoresis with electrophoresis buffer containing 25mM Tris, 192 mM glycine, and rest water if the sample being loaded is dissolved in methanol it won't remain in the...

15 December 2020 4,999 3 View

How to improve the organisation of my manuscript from poor to good?

Several time i received this comment from the reviewer that your manuscript organisation is poor. Please suggest me how to improve it.

24 November 2020 1,719 3 View

What is the most efficient way to measure the performance of a chatbot implemented using deep learning techniques?

The chatbot has been implemented using deep learning techniques. can anyone please suggest an efficient and effective way to measure the performance so that it can be compared with other...

20 November 2020 8,218 6 View

What statistical analysis test should I use?

I conducted a grammar test consisting of 36 questions divided into 8 categories. The categories form a cline, with category 1 being the prototype and category 8 being the furthest away from the...

10 October 2020 405 4 View

Does SWAT model not support high resolution gridded climate (0.25 degree) data?

Dear all, I have prepared rainfall datasets for SWAT MODEL using 0.25 degree IMD long term gridded rainfall data, but as I am using it in the model, it is rounding off the co-ordinates...

03 October 2020 421 5 View

Which NCD is likely to increase the most after Covid-19 pandemic is over?

We have seen that the mortality among the Covid patients suffering from NCDs is very high. So we need to protect NCDs patients from covid infection.But a rise is expected among NCDs after the...

23 September 2020 4,080 4 View

Which component of MPOWER toolkit has shown the highest impact in India since GATS -1?

We know there is a substantial reduction in tobacco use in India as per GATS-2. Which component of MPOWER toolkit has shown the highest impact in India since GATS -1?

25 August 2020 9,254 1 View

What is the best Free/Open Source software for doing Taguchi and other design of experiments and associated meaningful analysis like ANOVA?

Also what are the different efficient DOE and Analysis methods w.r.to machining operation with a specially sintered tool?

03 August 2020 4,553 3 View

What is the current research scenario related to solid lubrication & solid lubricant based cutting tools?

What according to you should be researched/accessed with respect to WC based solid lubricant tools? What is your view with respect to future research in this area? (For e.g. Tribological study...

19 July 2020 3,232 6 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

Md. Abdur Rahman

You can gather information on the processing, characterization and applications from the following link.

https://www.sciencedirect.com/science/book/9780124016989

https://www.reade.com/products/aluminum-lithium-al-li-alloys

https://en.wikipedia.org/wiki/Aluminium-lithium_alloy

Article The Evolution of Al-Li Base Products for Aerospace and Space...

http://www.samaterials.com/aluminium/1298-aluminum-lithium-alloy-al-li-alloy.html

Article Modern Al – Li alloys and prospects of their development

https://www.nap.edu/read/5070/chapter/5

Pranjal Chauhan

Thanks to you guys for your kindly help, what you mention benefit me a lot, which helps me to understand this better.