Can anyone share basic Security Constrained Unit Commitment code here?

11 November 2018 0 8K Report

i want to save my time for re-coding. Thanks in advance

Badges
Science topic

More Aamir Nawaz's questions See All

How to determine line shift factors for different scenarios of power system with high penetration of wind farms?

For example, if I want to find the stochastic OPF of a system, shift factors can provide a way to find shifted power for different scenarios. Therefore, OPF for each scenario is not required but...

09 October 2019 6,944 9 View

Can anyone provide code for Consensus + Innovations and Optimality Conditions Decomposition?

I need code of Consensus + Innovations and OCD in any programming language preferably Matlab or R

04 May 2018 2,462 2 View

Can anyone share Probabilistic Analytical Target Cascading code in matlab or GAMS or any language?

I need PATC code in any language preferably matlab.

04 May 2018 5,393 5 View

Does any one have coding for Reliability Evaluation and Risk assessment of Power system?

I need code in any programming language, preferably in matlab or R. I just dont want to code it from scratch. So please let me know if any one can help.

08 September 2017 3,827 3 View

How to develop a simulink model for power system frequency variation with load variation?

I have found out that synchronous generation in matlab auto-adjust frequency if load increase or decreases. So how to create such model in which frequency can be disturbed by load increase or...

07 August 2017 6,100 3 View

How to transform input variables of two systems and project on output side to show uncorrelated output with reasonable correlation and copula output?

Two systems give uncorrerlated or less correlated outputs while their inputs show some correlated behavior. So how to transform and find some complex relationship between inputs-outputs which can...

04 May 2017 4,278 2 View

Anyone worked on calling Python functions into R software?

Moreover, rPython is currently not working in R for windows environment.. Suggestions will be highly appreciated

04 May 2017 9,684 4 View

I need some information or some reference book or research paper on Ramping capability of operating reserve?

Integration of Wind farms and PV Solar power plants

08 September 2016 5,053 0 View

Where can I find official data of IEEE test power systems?

I am working economic load dispatch problem and need load, demand and loss coefficients data for evaluation. Can any one recommend me exact url of IEEE or any other standard source of above...

11 December 2014 4,678 8 View

How do I call the nlconst.m function within other functions using the function handler under MATLAB?

I am using nlconst.m for constrained minimization of given function. but when i call nlconst() with some points as inputs arguments, i get error "OPTIONS is undefined". What OPTIONS can be used in...

10 November 2014 3,148 1 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there a classification scheme for rock cavities or caverns with respect to their size and shape?

The range of forms and sizes of cavities in rock is very big. Is there a classification scheme for rock cavities regarding their size and shape?

02 March 2021 4,511 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View