Can anyone provide me with an ABAQUS model which employs "concrete damage plasticity" or "concrete smeared crack" in a beam?

More Morteza Tahmasebi Yamchelou's questions See All

Is there any other method than freeze-drying (lyophilization) to stop geoplymerisation reaction?

Dear scholars, Is there any method other than freeze-drying (lyophilization) to stop the geopolymerisation reaction from going on? I'm grinding the geopolymer samples down to a powder for NMR and...

05 June 2019 5,464 4 View

How to calculate the amorphous content of a sample?

Dear scholars, I run XRD on raw and calcined clay and I do expect the calcined clay to exhibit higher amorphicity according to what I have read in the literature. The instrument and the software...

04 May 2019 5,888 12 View

Is there a software to identify chemical bonds form FTIR spectrum?

Dear scholars, Is there any software for identifying the chemical bonds existing in FTIR spectra of inorganic materials? I have reviewed the literature and there are some tables which assign the...

31 December 2018 2,497 2 View

How to adjust the background (curvature and threshold values) in DIFFRAC.EVA?

Dear scholars, I am performing an XRD test on a powder clay sample (passed through 45 micron mesh size sieve) to determine its amorphous content. Depending on the curvature value I select in the...

08 September 2018 4,760 5 View

How to develop Moment-Curvature graph in ABAQUS software?

Dear Scholars, I'm using 2D and 3D continuum plain stress element to investigate the bending behaviour of a beam in ABAQUS, but for CPS8 element (plane stress 2D or 3D) section curvature and...

05 June 2018 3,309 7 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Natividad Garcia

Have you read about concrete damaged plasticity in the Abaqus documentation (section '18.5.3 Concrete damaged plasticity' in the ABAQUS manual) ?

http://130.149.89.49:2080/v6.7/books/usb/default.htm?startat=pt05ch18s05abm36.html

Morteza Tahmasebi Yamchelou

Thanks for the link. yes, I have read the documentation. I'm just in need of a sample model.

Best

I am attaching two papers that can be very helpful for your case