Can anyone provide me the wtckoff position of alpha fe2o3 and gamma fe2o3?

More Manas ranjan Sahoo's questions See All

Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

How to classify and recognize unseen image class in document sorting?

To sort the scanned document image I have to determine the class of document. But no of classes of image will keep on adding even after training. So at time of inference first I will detect unseen...

16 February 2021 4,501 3 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to modify micro-structure of Pure Copper which is available as a flat plate of 25 X 25 sq. cm?

Hi everyone, for a thesis project I have to modify the micro-structural properties of pure Cu flat plate of dimension 25 X 25 sq. cm . As I tried searching the available literature, I found a lot...

09 February 2021 5,090 3 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

After G actin polymerization and labelling I didn't got filaments. Why?

Purified G actin and got 42kda band and an additional band just below it. While performing G actin polymerization and labeling with rhodamine-phalloidin I didn't observe filaments under the...

20 January 2021 3,751 2 View

I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Gert Nolze Popular answer

You should spend s littel bit time and look e.g. at COD (follow the link)

http://www.crystallography.net/cod/search.html

Gert Nolze

P. Grima Gallardo

In addition to the web page suggested by Dr. Nolze you can also use: http://crystdb.nims.go.jp/index_en.html

Best regards

Pedro