How can i design a applicable antenna for a metal detector?

i need to know about metal detector antennas (loop), i want to construct a metal detector based on MATLAB software real time capability, software for design and implementation of antenna, thanks all,

02 March 2016 8,453 1 View

How can I run simulink and m.file coordinated in matlab?

11 December 2014 8,367 6 View

How can I solve the low speed of my simulation in simulink?

I have a multi machine power system, and I had to simulate it by solving differential equations of the whole system in simulink, but the speed of the simulation is very low, how can I do this...

09 October 2014 1,950 16 View

Can any one help me with this error in matlab?

Error using checkSingleTaskingSolver (line 31) Error due to multiple causes. Error in dlinmod (line 183) if ~checkSingleTaskingSolver({model}) && simstat Error in linmod (line...

03 April 2014 7,663 2 View

How can I calculate eigenvalues in matlab?

When I use the "linmod" and " damp" command in my cost function, it gives errors and I can't solve it.

03 April 2014 7,256 4 View

How can I make a 3-phase fault at the terminal of a generator in MATLAB?

I want to study the stability of a single machine infinite bus system with MATLAB. My problem is not in simpower systems, but in simulink.

02 March 2014 5,306 4 View

Can some body help me with simulation of multi machine power systems in matlab?

16-machine, 10-machine, etc.

02 March 2014 9,773 3 View

How do I simulate a nonlinear model of a single machine infinite bus system in matlab?

In addition to Simpower.

02 March 2014 2,294 18 View

What are the recently multi-objective optimization algorithms? Which one is the best?

I need a multi-objective optimization algorithm

01 February 2014 3,568 13 View

How can I do a nonlinear simulation of single machine infinite bus system in matlab?

I want to simulate nonlinear state space equations, I need it for stability analysis.

01 February 2014 9,462 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View