Can anyone help me on how to plot scattering pattern of a reconfigurable metasurface(IRS) in CST software?

04 August 2022 1 5K Report

I need to observe the beam steering of a programmable IRS structure In CST software. Can anyone help me with the procedure to plot scattered radiation patterns in CST?

Smrity Dwivedi

Hello,

Few papers are attached.

Thanks,

Badges
Science topic

More Malleboina Raju's questions See All

Which transition metal salt precursor is best for doping? Why?

I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...

27 February 2021 4,285 3 View

Sequence of an unknown Oligonucleotide ?

Hi All, I do have a single-stranded oligonucleotide of 100 - 150 bases synthesized and the sequence is not known. How would I proceed to know the sequence .

04 February 2021 5,614 3 View

How to separate solid NHS-folate during the folic acid activation?

Am functionalizing the metal nanoparticle with folic acid. in the process I have taken folic acid in DMSO and added DCC and NHS to activate the carboxylic acid group of folic acid in the standard...

01 February 2021 9,890 3 View

In online GC-FID/TCD connect to flow reactor, why I am getting instable peak area in FID in every injection under same conditions?

We have online GC-FID and GC-TCD (Mod: 2014) connected with flow reactor system. This GC-FID/TCD is connected to a gas line coming from flow reactor system which I used for cascade reaction. In...

11 November 2020 4,999 6 View

Please suggest that the way of obtaining the concentration (in mol) from the gas mixture (N2=98%, Ethylene=1% and Butadiene=1%) is correct or not?

I have a gas mixture (N2=98%, Ethylene=1% and Butadiene=1%). I want to obtained the molar concentration of each components for 1mL volume of the gas mixture. For that purpose, I have used the...

29 September 2020 6,233 1 View

What should be the minimum and maximum dopant concentration to achieve best photocatalytic activity of any semiconductor?

I am working on modifying the band structure of TiO2 semiconductor for visible light photocatalytic activity. For this reason, I would like to dope the metal and/or nonmetal ions into the TiO2 to...

23 September 2020 1,063 6 View

How to calibrate a GC-FID where two of the components are gas phase & others are in liquid phase?

I am new in GC-FID and TCD measurement technique. I will analyze a gas stream at high temperature above 190 oC in the GC-FID system. I want to construct a calibration curve for the mixture of...

08 September 2020 6,073 3 View

Anybody has an experience on the DSSAT 4.7 model ? please let me know?

I am working on the DSSAT model, its a little bit harder than I think please help me?

04 May 2020 5,708 3 View

Why are the COVID-19 infection and mortality rates lower in India?

It is intriguing that the number of reported cases infected or died due to COVID-19 infection in India is comparatively much lower than the United States (US), China and other European countries.

18 April 2020 2,170 22 View

How to convert netcdf file in *.nc4 format to .csv or excel format containing data on planetary boundary layer height?

Monthly average data on Planetary boundary layer height is downloaded from disc.gsfc.nasa.gov. It is in netcdf file in *.nc4 format. How to convert this into .csv or excel format ?

15 December 2019 8,137 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

What is best solution for optical metamaterial design calculation: HFSS, COMSOL, CST?

Dear all, Now I'm selecting FEM for design of metamaterials on NIR~VIS frequencies, and keeping 3 software: ANSYS HFSS, COMSOL with wave optics module, and CST STUDIO SUITE. Could you give me...

09 February 2021 9,517 2 View

Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View