Calcium recovery in steel

Dr. Pallavi Deshmukh @Dr-Pallavi-Deshmukh

01 January 1970 1 10K Report

Dear All,

How the recovery of Ca in steel is related to the cleanliness of steel?

Higher is the % of formation of CaO, CaS, calcium aluminate in steel lower will be the recovery..then why steel industries are aiminig at higher Ca recovery %?

Dr. Pallavi Deshmukh

Is the Ca% in the slag is determined? if it is so then higher the Ca% in slag better is the performance of CaSi...please give your expert input

Badges
Science topic

More Dr. Pallavi Deshmukh's questions See All

Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

Problem in energy minimization using Gromacs?

I have done energy minimization of DNA using Gromacs with tutorial lysozyme in water. The potential energy curve show a steep drop.

18 February 2021 4,822 2 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

What is the best method for preparation of Polymeric nanoparticles for co-delivery?

We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.

09 February 2021 7,086 8 View

OmniScriptum Publishing Group?

Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...

08 February 2021 5,611 3 View

Which one is better for storing energy: Fuels synthesized from CO2 or Hydrogen?

Based on educated guesses, which one of the following promises a better future for storing energy for grid scale, automobiles etc as opposed to batteries: 1) Fuels synthesized form CO2 2)...

02 February 2021 8,741 6 View

Is there any software to generate pdb of G quadruplex?

I have a DNA sequence which has predictability to form G quadruplex . I need a software to generate a pdb of it which will form G quadruplex. I am using open Babel but I am not able to set the...

29 January 2021 6,190 4 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

How much Ti and B (in ppm) is required for effective grain refinement and why?

To have the desired grain size in 6061 and 6063 Al alloy, what should be the minimum % of Ti and B pick up and what is the chemistry/metallurgy behind that?

07 January 2021 9,305 2 View

How to make AlV50% alloy by thermit route?

Kindly provide the technical papers/patents on the production of AlV50% alloy by thermit route, by using V2O5

05 January 2021 2,471 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Is there any research regarding how training and development is going to change in the era of Fourth Industrial Revolution?

As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...

01 March 2021 3,199 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Is anyone working on a project focused on immigrants/newcomers working in the hospitality industry and how they have been impacted by COVID?

The on-going Covid-19 pandemic has had devastating economic effects on many industries. However, few have suffered to the same extent as full-service restaurants. Numerous studies have shown that...

24 February 2021 9,496 4 View

What is the optimum time and temperature of blanching and pre-frying potato for frozen fries?

I am helping a local home industry for developing frozen fries from their local farm. I want to know what is the optimum blanching and pre-frying temperature and time for processing. Please also...

23 February 2021 1,616 5 View